- Help!! Pressure loss of air poppets (14 replies)
- SAP2000 link displacement and joint displacement (0 replies)
- Resource for designing with Bearings and Gears (2 replies)
- Infrared Drying for firecrackers. Possible? (6 replies)
- Happy Thanksgiving to all within the USA! (0 replies)
- Looking for articles discussing angle axis differences between holes and screws (3 replies)
- Teamcenter over SAP PLM (1 replies)
- excel input (4 replies)
- Question on how to design locking mechanism? (3 replies)
- Mechanical mechanism help (2 replies)
- Resistive heating vs. Hot pack (1 replies)
- Pushing water along. (6 replies)
- Product Design Question? (3 replies)
- Help needed - Secondary Auxiliary view drawing ! (1 replies)
- acme thread wear issue (5 replies)
- I've hit a prototype wall (12 replies)
- Tripod leg end conditions, and a few other questions (0 replies)
- Small Gain Machine using Hydraulic Ram Pumps (1 replies)
- Delta T Cooling time (1 replies)
- real-time ECG? (2 replies)
- Software for the following engineering sketch? (1 replies)
- Properties of A36 Steel at -40°C Ambient (0 replies)
- Hydraulic lift design (2 replies)
- Help needed please - Toggle mechanism force calculations (12 replies)
- Vacuum Chambers (4 replies)
- Newbie looking for advice on a hydraulic press fixture producing 60 tons... (4 replies)
- Help with a device for sliding an object down a sheet of ice (0 replies)
- Motor Torque Requirement (1 replies)
- Software for Tracking changes between 2 Engineering Drawings? (1 replies)
- Engineering Training - Do we need it? (8 replies)
- help needed, how to heat a copper sheet (4 replies)
- lever calculation (4 replies)
- Bearing Overload? (2 replies)
- Design (3 replies)
- What is a UPS pump? (2 replies)
- water sensor umbrella .. (1 replies)
- Strength of Material (4 replies)
- Gear horsepower calculation (1 replies)
- What Bearing do I need for Running Under Water? (7 replies)
- Help for rotatable foundation (copper sleeve and guide-rail in combination) (1 replies)
- Need some help solving a small design problem (1 replies)
- Power and Torque Calculation for a Motor (1 replies)
- Need help consolidating my project components (0 replies)
- Help design a conical compressor (11 replies)
- sap2000 joint displacement (5 replies)
- Building a porch frame to hold paver blocks (1 replies)
- HELP!!! Basic Statics Question (6 replies)
- Hollow Bolt Shanks (1 replies)
- Help with calculating weight that steel tubing can handle (12 replies)
- hydrogen powered turbine (1 replies)
- Design of tiny CO2 cartridge. (9 replies)
- Travel Trailer Drawing (0 replies)
- How to submit a drawing on Travel Trailer Rear Hitch (1 replies)
- Medical Imaging System Design - Standards? (0 replies)
- travel trailer rear hitch (21 replies)
- Parbuckling - Engineering Word... (2 replies)
- Using servo motors to actuate intake and exhaust valves (7 replies)
- Baby Incubator Design Project (2 replies)
- Steel Angle Plastic Section Modulus (1 replies)
- Load-bearing column (1 replies)
- Please, need help selecting the right motor for a design I am building. (0 replies)
- Calculating flexion in curved tube (4 replies)
- Looking for books about: building and designing of trailers (2 replies)
- additional beam support with angle iron (1 replies)
- Battery Powered Mini-Cable-Car (2 replies)
- Why didn't you do a more lucrative or easier career? (10 replies)
- Remotely Actuated On-Off Valve (1 replies)
- Compressibility of Water Constant (1 replies)
- Engineers Club Buy and Sell is Now Free (0 replies)
- Joining pipe to a flat surface (12 replies)
- Beam Weld Joint Hurry (3 replies)
- Permanent magnet and electric magnet repulsion and attraction (1 replies)
- ID change due to heating on a press fit polymer bearing (4 replies)
- Thermodynamics/Heat transfer software packages (4 replies)
- Steampunk Air Ship (3 replies)
- need help with heat transfer problem. urgent (1 replies)
- Strength of Steel (1 replies)
- Is it possible to calcuate this? (4 replies)
- liquid ring vacuum pump (2 replies)
- Interested in a new career in engineering... would love some advice (3 replies)
- Heat Plate in Air to Melt Plastic (3 replies)
- Which of these poses more of a software and hardware engineering challenge? (2 replies)
- Buckling Strenth of pipe with non-axial load (1 replies)
- Flip Flop circuits (1 replies)
- Slow Motion of an AK-47 Underwater Part 1 (1 replies)
- Help with nomenclature? (2 replies)
- device to let air out but not water under pressure (2 replies)
- Help making a timed pressure release that can have time accuracy of tenth/second (2 replies)
- Section Modulus Help (6 replies)
- Stopper Position in Fixture (0 replies)
- Two bolt versus single bolt clamps. (3 replies)
- Wind Force Calculation (0 replies)
- clamping force (2 replies)
- steel plate deflection 1/2 inch (5 replies)
- Threaded Insert or Not (9 replies)
- Force due to Magnets (2 replies)
- Beam Calculations for Load (5 replies)
- Calculate Tension (2 replies)
- How to build an RF transmitter? (2 replies)
- engineering in 5 years (2 replies)