- Reactions Calculations (1 replies)
- Determination of load cycle for automobile bearing (0 replies)
- Bent plate cantilevers from wall (0 replies)
- Drive line Calculations (1 replies)
- 6m x 2m x 2m Trailer Design and Materials questions (0 replies)
- My Hypothetical Hypersonic Jet Engine (With No Moving Parts... Promise!) (4 replies)
- Ball throwing mechanism (0 replies)
- Trying to join PVC parts together (2 replies)
- Designing of a baler machine (0 replies)
- Identifying a force (6 replies)
- identifying proper motor (3 replies)
- Tank Considerations: Pressure vs Vacuum. (3 replies)
- How do you like Design Engineering? (1 replies)
- Fundamentals of Design Engineering? (4 replies)
- No. of Holes (5 replies)
- Concentric Rings with constraints (0 replies)
- transmission project (0 replies)
- Learning about turbines and thinking about the output. (2 replies)
- Best spline type - rotational force into plastic (0 replies)
- Rule of thumb strength question. Brass vs stainless steel (2 replies)
- Rule of thumb for drilling holes in I beam flange (3 replies)
- Machinery's, Roark's Stress and Strain, etc. (3 replies)
- Motor with brake and gearbox for high torque application (1 replies)
- what kind of electric motor with reducer is needed? (0 replies)
- Deflection and Stress of arm with an angle (1 replies)
- Tempered glass "burst" calculation (0 replies)
- Structural safe loading calculation (1 replies)
- Motor and Gearbox Pairing (2 replies)
- Physical height calculation of RA surface finishes. (1 replies)
- Back yard jet engine? (1 replies)
- Stainless steel floor drain (4 replies)
- Pneumatic hammer prototype (1 replies)
- Pre-load on needle roller clutch (1 replies)
- Lever arm design (2 replies)
- Heat Exchanger Question (1 replies)
- Uni project Help (0 replies)
- SolidWorks Stress Analysis question (2 replies)
- Material "Slash sheet description" (0 replies)
- Need for advice (1 replies)
- Air tanks in parallel and series (2 replies)
- Reference for Table (1 replies)
- Plastics Shredder Design (1 replies)
- Ways to lessen wear caused by a steel fixture (5 replies)
- Help Plz!!! Scissor Lift, need help. (0 replies)
- Help Needed figuring out weight load of angle iron please (1 replies)
- Help needed in determing the tip load capacity of a particular pole type (7 replies)
- Motorized Stages for smallest incremental movement possible? (1 replies)
- Who Is The Manufactuerer of this Heavy Hex Nut (2 replies)
- How to reduce deflection on this DIY table. (3 replies)
- Rivet related question, how many and what size? (0 replies)
- help to estimate the pulling force in this pulley-cable arrangement (2 replies)
- Ab Toning Systems (3 replies)
- Low Friction Fabrics (5 replies)
- Remagnatizing (1 replies)
- Four Bar Linkage Angles (1 replies)
- Industrial Vacuum Chamber Design - Need Help for Design Calculations (0 replies)
- How to manufacture this spiral part? (2 replies)
- Gas fired boiler efficiency calculations/ through losses (0 replies)
- Engineering ********** that combine mechanical, electrical and programming (3 replies)
- Missing eddy currents in copper? (0 replies)
- Shear stress on spline teeth (3 replies)
- Surface Finish After Anodizing Process (2 replies)
- Torque requirement calculation (3 replies)
- Real world rigging problem (8 replies)
- Help needed to design a bed on a winch/pulley system! (5 replies)
- What are the best practices for machining Aluminum? (1 replies)
- Pressure Vessel Design (1 replies)
- Tolerances (1 replies)
- Tubing size for cantilevered aluminum beam (5 replies)
- perforated beam (1 replies)
- Help with Proper Torque Spec (6 replies)
- Lubrication question (0 replies)
- How to get the best pressure control for branches (1 replies)
- Cutting 1060 plate (6 replies)
- simple mechanism to open and close dual sliding Barn Doors (1 replies)
- Identifying a piece of hardware holding a radio telescope dish (1 replies)
- i need a help in project related to mechanics and design (0 replies)
- Surface Finishes by Tolerance (1 replies)
- hydraulic pump/ motor question (0 replies)
- Find force of bolt (2 replies)
- Can anyone help me identify which material is better? (4 replies)
- UHMWPE question... two tubes of same material in exact same use/wash conditions etc (1 replies)
- Resolution of Forces and Moments on a machine structure (2 replies)
- New here. Bolt question (6 replies)
- Difference between 2 waterwheels (1 replies)
- Allowable bearing capacity (0 replies)
- How to determine the force on the linkage (0 replies)
- Restoration of Connection in Precast Concrete Structure (0 replies)
- Question about True Position (Cartesian Tolerance) (3 replies)
- Functional and autonomous smartphone (2 replies)
- Cyclic Loading of Fastener and Fatigue (5 replies)
- How To Calculate Forces In A Sheet Metal Bender? (2 replies)
- Rotation using two (four) hydraulic cylinders HELP! (0 replies)
- Hollow cone beam loading question (1 replies)
- Conductive Gels of shore OO or softer (1 replies)
- Assist with Miniature Bearings Selection for WINDSWIMMER Prototype. (1 replies)
- Requirement Analysis (0 replies)
- shear pin diameter (2 replies)
- Hinge design (2 replies)
- Bad Connector Design / Choice (2 replies)