- Smart measuring instrument (2 replies)
- Really good reasons to have in-house 3D printing (3 replies)
- Beam deflection (8 replies)
- Is this possible? (7 replies)
- How much would it cost to remove this wall? (1 replies)
- can't identify the root cause of the rust (1 replies)
- Rotted floor joist repair? (0 replies)
- Question: Title Block Default Tolerances (1 replies)
- Copper Heat Sink Design Help (0 replies)
- 1.5 -2.0 mm wire rope tapered end (0 replies)
- Structural Beam Stress and Deflection Calculations for Non-Engineers (0 replies)
- Bolt Anchor Plate Design (1 replies)
- What is your preferred quick extrusion profile size? (1 replies)
- NAAMM AMP510-92 questions. (4 replies)
- MOC vs RIK stories needed (0 replies)
- Machines using fast-moving pumps/cylinders/compressors (1 replies)
- Angle iron stand strength for a fish tank stand (10 replies)
- guideline needed (5 replies)
- Is high-quality tooling with quick aluminum extrusion possible? (5 replies)
- Building a portable storm shelter (3 replies)
- Calculating axle strength (0 replies)
- Need Review for my idea (3 replies)
- What is view factor for two concentric cylinders ? (0 replies)
- Which kind of bearing to be use for axial shaft submerged in water/oil (2 replies)
- Helical plate bending (5 replies)
- House Addition and changing Structural Beams (or material) (0 replies)
- Career help - next step after Bachelor in Chemistry? (2 replies)
- Please help finding program to learn basics with... (5 replies)
- Help! Possibly switching careers to biomedical engineering. Input appreciated :) (3 replies)
- Lead Screw nut Force vs drive Torque (0 replies)
- 5120H Steel Round (1 replies)
- Sistering floor joists with a span of 11.5' (1 replies)
- Alignment of Generator with Gear Box Coupling (0 replies)
- Need help with using force gauge (6 replies)
- strength comparison between 6x6 pressure treated wood and 4x4 steel square tube (0 replies)
- Sling length for a basket hitch with two slings - More of a Geometry question. (9 replies)
- What the heck is this?!?!?! (0 replies)
- Fixing sagging flat roof joists (2 replies)
- Beam Removal? (4 replies)
- fundamental calculations - explanation (1 replies)
- Reasonable deflection for a metal and wood table (20 replies)
- Finding power to move cart (2 replies)
- Figuring the flow rate and pressure of an air horn (3 replies)
- gland nut torque spec (4 replies)
- Thrust Load on an Angle (1 replies)
- LVL sizing (0 replies)
- Deviate from a mil spec? (2 replies)
- Difference between world electricity generation and consumption? (0 replies)
- pressure torque conversion (3 replies)
- Designing my own mobile phone (0 replies)
- Diametral Pitch Question (2 replies)
- How to design this kind of plastic object (1 replies)
- What type of paint/coating to to get matte smooth finish (1 replies)
- Ceiling Support (3 replies)
- Any chance MEP designs can be done within 4 days with excellent quality? (2 replies)
- Calculating Pull Force Based on Bolt Torque (3 replies)
- Proper beam selection (5 replies)
- Calculation for vacuum creation in heat exchanger (0 replies)
- Calculating maxium weight for a goods trailer (0 replies)
- Press brake punch depth and angle formulas (6 replies)
- American standard Keys and Keyseat (4 replies)
- effective height of a tall building including foundation-soil interaction (0 replies)
- Which Size I should choose? (0 replies)
- Ideas on constructing a spherical shell with a variable mass (0 replies)
- How is energy dissipated in a nail gun test rig? (0 replies)
- How can I deconstruct this project in a safe way? (1 replies)
- Help engineering design on bearing swivel for a Pole to mount a 1000lb plane windvane (0 replies)
- Help with an insulated camera box - high temperature (1 replies)
- Force on a vertical angle (1 replies)
- digital signal processing (0 replies)
- Making a Small Crane to Lift Boudlers (9 replies)
- spreader bar help (1 replies)
- Swaged Flemish eye pulled over a sheave (1 replies)
- Assembly clamp idea needed (0 replies)
- fastener torque to axial force (3 replies)
- Sheet Metal Design and Manufacturing (3 replies)
- removing raised floor level (3 replies)
- Simply Compression and Tension experienced on piston problem. (0 replies)
- Aluminum I-beam to replace wood beam (5 replies)
- Box steel or angle iron ? (1 replies)
- EES Help (1 replies)
- REverse Deep Drawing (0 replies)
- Hydraulic Jack 12 Volt DC - Engineering College Project, Need Suggetions. (3 replies)
- Looking for resources on methodologies of collapsing containers (0 replies)
- Beam Strength Question (1 replies)
- 76'diameter trapezium dome (3 replies)
- Fractional horsepower gearbox lubrication (4 replies)
- Help with Plane frame analysis (1 replies)
- Joining two brass components - advice? (8 replies)
- Aluminum Cross Members for Roof Rack (0 replies)
- Handling parts off of lasers sharing material towers. (1 replies)
- How to clamp a thin (0.015") wire without knotting it? (1 replies)
- Force required to anchor frame (0 replies)
- Name of component? (9 replies)
- How to calculate required Power in KW for Trolley (0 replies)
- Conveyor Capacity Calculations need help please! (0 replies)
- 4 stage pumped water filter (0 replies)
- Catching wind to rotate a load (1 replies)
- Wireless Power Transmission (1 replies)
- Involute Gear Design - Dedendum Base Circle Relationship (1 replies)