PDA

View Full Version : Dimensioning Tolerancing GD&T Discussion Forum | GD&T Training


>

Pages : 1 2 [3] 4

  1. Positional Tolerance for Hexagonal Features
  2. GD&T Help
  3. Hole referencing a perpendicular plane
  4. Where in Y14.5M is Third-Angle Projection identified as the default?
  5. GD&T Composite Feature Control Frame
  6. Die Set Hole Position Tolerance
  7. Old drawing gdt
  8. Hole and Peg tolerance
  9. GD&T Datum References
  10. Noob to gd&t needing guidance
  11. Datum Target Application on Drawing
  12. Question on Datum Reference Frame
  13. Is this a method of GD&T simultaneous referencing?
  14. Rookie needing some help with GD&T questions
  15. Positional Tolerance of FHCS's???
  16. Go-gage help
  17. Pattern of 4 slots as datum
  18. GD&T (workbook)
  19. Older engineering drawing symbols
  20. Gd&t for a radial hole
  21. Position of round slot
  22. Applying the correct Dim.
  23. GD&T Position Tolerance and continuous Feature symbol application
  24. GD&T Is this dimension ±.002 or .002 Max?
  25. Can 3 square holes in an L formation be called out as Datum B?
  26. positional control and datum references GD&T
  27. ISO standard GPS and dimension tolerances and iso 8015 standard
  28. Problem understanding those callouts
  29. Which dim to use?
  30. Datum Features
  31. Flatness Actual Value
  32. Reporting True Position from Off Plane and Angled Holes
  33. GD&T on a dovetail feature
  34. Concentricity on the thread
  35. True Position Calculation Question
  36. Datum use on round part
  37. Gd&t true position with basic angle
  38. How to provide concentricity tolerance in assembly?
  39. Hole Pattern with GD&T
  40. Proper way to dimension diameter of cylinder
  41. Calculate Ra
  42. What is the difference between these two situations?
  43. Please help answer this question
  44. GD&T callout for sharp edge
  45. Straightness Tolerance on a Turned Part
  46. Basic dimension tolerance
  47. Angularity vs Perpendicularity on a Dovetail
  48. Calculation of Maximum Material Boundary
  49. Feature of size question
  50. Positional tol on pcd
  51. Help me understand this please:
  52. GD&T Angular Datum Question
  53. Envelope Principle
  54. GD&T questions
  55. Three (3) Point Suspension System for Measuring Flatness
  56. No tolerance given.
  57. Profile and Flatness tolerance
  58. Drawing Symbol
  59. Virtual Condition Check with RFS
  60. Diametrical True Position - need clarification
  61. GD&T Examples?
  62. Datum representation
  63. How to Interpret Geometric Tolerance and Dimensional Tolerance
  64. Profile of a line: implied 'symmetric' constraint
  65. Position on coaxial features
  66. How calculate tol position datums mmc
  67. Question about tolerances
  68. Title block tolerance applied to hole diameter with geometric positional tolerance
  69. Referencing .STEP file as Basic Geometry
  70. Is my tolerance stackup correct?
  71. Position tolerance with circularity
  72. Callout for threaded hole to be tapped straight
  73. Basic or not?
  74. GD&T floating Fastener Formula question
  75. Trends in Trainings on Engineering Standards
  76. Best Way to Dimension Circular Features
  77. Economics / Cost of Applying GD&T
  78. I need help
  79. Using Square Symbol on a square hole pattern
  80. Drilled Hole positioning query on threaded bolt
  81. ISO hole size tolerance
  82. ISO standard GPS and dimension tolerances and iso 8015 standard?
  83. theoretically exact dimension question
  84. New Engineer learning GD&T with some questions
  85. True Position of ZERO
  86. More than One Surface Finish Symbol on Drawing
  87. applying significant digits to a geo tolerance in a feature control frame
  88. Specifying tolerances for multiple features in press fit
  89. modifier on dimensions
  90. Interpretation of DRF
  91. Specifying perpendcularity for odd pipes
  92. MMB Calculation - Special Case
  93. LMB y MMB
  94. BS-8888 Concentricity on turned parts
  95. Similarity of LMB (Least Material Boundary)
  96. Tolerance to centerline allows negative
  97. 2Way datum hole profile tolerance
  98. GD&T Is the flatness error of the datum feature irrelevant when checking parallelism?
  99. Datum on "angular slab" centerline?
  100. GD&T Linear Distance from Edge to Edge