Page 1 of 75 1 2 3 11 51 ... LastLast
Threads 1 to 20 of 1493

Forum: Engineering and Design Main Forum | Engineers Edge Forums

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 9,111
    11-15-2018, 12:07 AM Go to last post
    • Replies: 1
    • Views: 37
    09-16-2019, 02:29 PM Go to last post
  1. Back yard jet engine?

    Started by iamramondreddington, 09-12-2019 07:46 AM
    • Replies: 0
    • Views: 171
    09-12-2019, 07:46 AM Go to last post
  2. Stainless steel floor drain

    Started by iamdemberedingtonsbodygaurd, 09-11-2019 10:48 AM
    • Replies: 2
    • Views: 236
    09-11-2019, 06:00 PM Go to last post
  3. Lever arm design

    Started by lavdesesamajmeayakya, 08-30-2019 06:42 AM
    • Replies: 2
    • Views: 547
    09-05-2019, 02:18 PM Go to last post
  4. Pneumatic hammer prototype

    Started by cjccmc, 08-30-2019 03:23 PM
    • Replies: 1
    • Views: 507
    09-03-2019, 12:45 PM Go to last post
  5. Pre-load on needle roller clutch

    Started by csendegeya, 08-30-2019 09:35 AM
    bearings, clutch
    • Replies: 1
    • Views: 475
    08-30-2019, 10:21 AM Go to last post
  6. Angle Iron Stress

    Started by komet99, 04-03-2012 09:48 PM
    • Replies: 9
    • Views: 65,936
    08-28-2019, 01:31 PM Go to last post
  7. Heat Exchanger Question

    Started by belachavbelachavchavchavchav, 08-22-2019 03:14 PM
    • Replies: 1
    • Views: 609
    08-23-2019, 08:27 AM Go to last post
  8. Uni project Help

    Started by Prialen08, 08-21-2019 09:41 AM
    design, jockey wheel
    • Replies: 0
    • Views: 538
    08-21-2019, 09:41 AM Go to last post
  9. Low Friction Fabrics

    Started by benjamin_banks, 05-01-2019 12:51 AM
    fabric, fashion, friction, material, science
    • Replies: 5
    • Views: 1,109
    08-15-2019, 10:41 AM Go to last post
  10. Ways to lessen wear caused by a steel fixture

    Started by harrisonczaj, 07-15-2019 10:47 AM
    fixture design, part wear, plastic coating
    • Replies: 5
    • Views: 900
    08-15-2019, 10:38 AM Go to last post
  11. SolidWorks Stress Analysis question

    Started by thinds, 08-12-2019 10:50 AM
    • Replies: 2
    • Views: 514
    08-13-2019, 08:10 AM Go to last post
  12. Material "Slash sheet description"

    Started by sdicarlo, 07-31-2019 02:41 PM
    • Replies: 0
    • Views: 376
    07-31-2019, 02:41 PM Go to last post
  13. Question tolerances, machining and cost

    Started by Ayien, 01-17-2018 07:23 PM
    gd&t, tolerances
    • Replies: 5
    • Views: 1,155
    07-29-2019, 01:16 PM Go to last post
  14. Aluminum on plastic tolerance fit?

    Started by sebastian_thomas, 04-29-2018 02:05 PM
    • Replies: 1
    • Views: 942
    07-29-2019, 01:10 PM Go to last post
  15. Need for advice

    Started by boutheynamzoughui, 07-29-2019 04:40 AM
    • Replies: 1
    • Views: 419
    07-29-2019, 07:20 AM Go to last post
  16. Air tanks in parallel and series

    Started by rouncer81, 07-26-2019 05:04 PM
    • Replies: 2
    • Views: 453
    07-26-2019, 05:38 PM Go to last post
  17. Reference for Table

    Started by halstedj, 07-26-2019 12:06 AM
    reference, source, table, thermal properties
    • Replies: 1
    • Views: 455
    07-26-2019, 07:21 AM Go to last post
  18. Red face Plastics Shredder Design

    Started by ramadhankd, 07-20-2019 08:19 AM
    calculation, invention, mechanical design, plastic, recycle
    • Replies: 1
    • Views: 659
    07-20-2019, 04:27 PM Go to last post
  19. Confused Help Plz!!! Scissor Lift, need help.

    Started by jw102033, 07-05-2019 10:07 AM
    • Replies: 0
    • Views: 940
    07-05-2019, 10:07 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •