Page 1 of 74 1 2 3 11 51 ... LastLast
Threads 1 to 20 of 1477

Forum: Engineering and Design Main Forum | Engineers Edge Forums

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 8,901
    petronextinternational
    11-15-2018, 12:07 AM Go to last post

  1. help to estimate the pulling force in this pulley-cable arrangement

    Started by naveenbnc, 05-09-2019 03:22 AM
    lifting, pulley 1 Attachment(s)
    • Replies: 2
    • Views: 1,223
    daleacyr
    06-18-2019, 12:16 PM Go to last post

  2. Help needed in determing the tip load capacity of a particular pole type

    Started by khknima86, 06-11-2019 06:28 PM
    • Replies: 7
    • Views: 415
    khknima86
    06-13-2019, 04:40 PM Go to last post

  3. Confused Help Needed figuring out weight load of angle iron please

    Started by jessyankey, 06-11-2019 07:56 PM
    • Replies: 1
    • Views: 394
    dalecyr
    06-13-2019, 12:30 PM Go to last post

  4. Motorized Stages for smallest incremental movement possible?

    Started by ajoseph, 05-30-2019 10:34 AM
    mechanical design, micro alignment, motorized stages
    • Replies: 1
    • Views: 759
    Kelly Bramble
    06-01-2019, 07:22 PM Go to last post

  5. Who Is The Manufactuerer of this Heavy Hex Nut

    Started by jds7748, 05-27-2019 08:42 AM
    1 Attachment(s)
    • Replies: 2
    • Views: 887
    jds7748
    05-27-2019, 09:04 AM Go to last post

  6. How to reduce deflection on this DIY table.

    Started by andrew_barrios, 05-23-2019 03:02 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 1,007
    Kelly Bramble
    05-24-2019, 01:48 PM Go to last post

  7. Rivet related question, how many and what size?

    Started by vexedne, 05-21-2019 02:18 AM
    • Replies: 0
    • Views: 971
    vexedne
    05-21-2019, 02:18 AM Go to last post

  8. Ab Toning Systems

    Started by benjamin_banks, 05-01-2019 01:00 AM
    body, fixing, skin, stickiness, suction 1 Attachment(s)
    • Replies: 3
    • Views: 921
    Cake of Doom
    05-02-2019, 05:08 AM Go to last post

  9. Low Friction Fabrics

    Started by benjamin_banks, 05-01-2019 12:51 AM
    fabric, fashion, friction, material, science
    • Replies: 4
    • Views: 906
    benjamin_banks
    05-01-2019, 02:39 PM Go to last post

  10. Gyroscope acts as a speaker to your balance system, not cochela

    Started by jtrevor49, 04-22-2019 10:45 AM
    • Replies: 1
    • Views: 778
    jboggs
    04-23-2019, 12:50 PM Go to last post

  11. insulation vs isolation

    Started by cynthiou, 08-11-2011 07:08 AM
    • Replies: 4
    • Views: 36,764
    samuelgeorge3443
    04-15-2019, 01:05 AM Go to last post

  12. Remagnatizing

    Started by vipera2006, 04-11-2019 07:10 AM
    magnets, remagnatazion
    • Replies: 1
    • Views: 457
    JAlberts
    04-11-2019, 11:28 AM Go to last post

  13. Four Bar Linkage Angles

    Started by busterinbox0, 04-08-2019 10:33 PM
    angles, fourbar, linkage 1 Attachment(s)
    • Replies: 1
    • Views: 408
    Hudson
    04-09-2019, 04:04 PM Go to last post

  14. Industrial Vacuum Chamber Design - Need Help for Design Calculations

    Started by pgallagher, 04-08-2019 07:39 AM
    1 Attachment(s)
    • Replies: 0
    • Views: 344
    pgallagher
    04-08-2019, 07:39 AM Go to last post

  15. How to manufacture this spiral part?

    Started by chrisrobertsonorr, 04-04-2019 01:49 PM
    2 Attachment(s)
    • Replies: 2
    • Views: 324
    Hudson
    04-05-2019, 11:08 PM Go to last post

  16. Arrow Gas fired boiler efficiency calculations/ through losses

    Started by anees, 03-19-2019 10:03 AM
    • Replies: 0
    • Views: 498
    anees
    03-19-2019, 10:03 AM Go to last post

  17. Engineering industries that combine mechanical, electrical and programming

    Started by danpsu2013, 03-16-2019 01:54 PM
    • Replies: 3
    • Views: 514
    jboggs
    03-18-2019, 07:27 AM Go to last post

  18. Missing eddy currents in copper?

    Started by yadnom1973, 03-12-2019 05:57 AM
    • Replies: 0
    • Views: 552
    yadnom1973
    03-12-2019, 05:57 AM Go to last post

  19. Shear stress on spline teeth

    Started by maksimb_93, 03-04-2019 12:07 AM
    1 Attachment(s)
    • Replies: 3
    • Views: 740
    maksimb_93
    03-05-2019, 08:56 PM Go to last post

  20. Torque requirement calculation

    Started by switzerf, 02-19-2019 03:23 PM
    • Replies: 3
    • Views: 722
    Hudson
    02-20-2019, 04:34 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules