Page 2 of 76 FirstFirst 1 2 3 4 12 52 ... LastLast
Threads 21 to 40 of 1515

Forum: Engineering and Design Main Forum | Engineers Edge Forums

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 03:46 PM
    • Replies: 10
    • Views: 9,282
    11-15-2018, 01:07 AM Go to last post
  1. Tempered glass "burst" calculation

    Started by ezetom, 09-23-2019 10:54 AM
    • Replies: 0
    • Views: 409
    09-23-2019, 10:54 AM Go to last post
  2. Stainless steel floor drain

    Started by iamdemberedingtonsbodygaurd, 09-11-2019 11:48 AM
    • Replies: 4
    • Views: 901
    09-22-2019, 11:49 AM Go to last post
  3. Back yard jet engine?

    Started by iamramondreddington, 09-12-2019 08:46 AM
    • Replies: 1
    • Views: 748
    09-19-2019, 03:16 PM Go to last post
  4. Structural safe loading calculation

    Started by sdubey, 09-18-2019 10:36 PM
    • Replies: 1
    • Views: 563
    09-19-2019, 05:13 AM Go to last post
    • Replies: 1
    • Views: 589
    09-16-2019, 03:29 PM Go to last post
  5. Lever arm design

    Started by lavdesesamajmeayakya, 08-30-2019 07:42 AM
    • Replies: 2
    • Views: 866
    09-05-2019, 03:18 PM Go to last post
  6. Pneumatic hammer prototype

    Started by cjccmc, 08-30-2019 04:23 PM
    • Replies: 1
    • Views: 808
    09-03-2019, 01:45 PM Go to last post
  7. Pre-load on needle roller clutch

    Started by csendegeya, 08-30-2019 10:35 AM
    bearings, clutch
    • Replies: 1
    • Views: 755
    08-30-2019, 11:21 AM Go to last post
  8. Angle Iron Stress

    Started by komet99, 04-03-2012 10:48 PM
    • Replies: 9
    • Views: 67,845
    08-28-2019, 02:31 PM Go to last post
  9. Heat Exchanger Question

    Started by belachavbelachavchavchavchav, 08-22-2019 04:14 PM
    • Replies: 1
    • Views: 835
    08-23-2019, 09:27 AM Go to last post
  10. Uni project Help

    Started by Prialen08, 08-21-2019 10:41 AM
    design, jockey wheel
    • Replies: 0
    • Views: 713
    08-21-2019, 10:41 AM Go to last post
  11. Low Friction Fabrics

    Started by benjamin_banks, 05-01-2019 01:51 AM
    fabric, fashion, friction, material, science
    • Replies: 5
    • Views: 1,221
    08-15-2019, 11:41 AM Go to last post
  12. Ways to lessen wear caused by a steel fixture

    Started by harrisonczaj, 07-15-2019 11:47 AM
    fixture design, part wear, plastic coating
    • Replies: 5
    • Views: 1,012
    08-15-2019, 11:38 AM Go to last post
  13. SolidWorks Stress Analysis question

    Started by thinds, 08-12-2019 11:50 AM
    • Replies: 2
    • Views: 618
    08-13-2019, 09:10 AM Go to last post
  14. Material "Slash sheet description"

    Started by sdicarlo, 07-31-2019 03:41 PM
    • Replies: 0
    • Views: 491
    07-31-2019, 03:41 PM Go to last post
  15. Question tolerances, machining and cost

    Started by Ayien, 01-17-2018 08:23 PM
    gd&t, tolerances
    • Replies: 5
    • Views: 1,275
    07-29-2019, 02:16 PM Go to last post
  16. Aluminum on plastic tolerance fit?

    Started by sebastian_thomas, 04-29-2018 03:05 PM
    • Replies: 1
    • Views: 1,025
    07-29-2019, 02:10 PM Go to last post
  17. Need for advice

    Started by boutheynamzoughui, 07-29-2019 05:40 AM
    • Replies: 1
    • Views: 510
    07-29-2019, 08:20 AM Go to last post
  18. Air tanks in parallel and series

    Started by rouncer81, 07-26-2019 06:04 PM
    • Replies: 2
    • Views: 545
    07-26-2019, 06:38 PM Go to last post
  19. Reference for Table

    Started by halstedj, 07-26-2019 01:06 AM
    reference, source, table, thermal properties
    • Replies: 1
    • Views: 529
    07-26-2019, 08:21 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •