Page 3 of 77 FirstFirst 1 2 3 4 5 13 53 ... LastLast
Threads 41 to 60 of 1531

Forum: Engineering and Design Main Forum | Engineers Edge Forums

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 03:46 PM
    • Replies: 10
    • Views: 9,451
    11-15-2018, 01:07 AM Go to last post
    • Replies: 1
    • Views: 682
    09-16-2019, 03:29 PM Go to last post
  1. Lever arm design

    Started by lavdesesamajmeayakya, 08-30-2019 07:42 AM
    • Replies: 2
    • Views: 930
    09-05-2019, 03:18 PM Go to last post
  2. Pneumatic hammer prototype

    Started by cjccmc, 08-30-2019 04:23 PM
    • Replies: 1
    • Views: 885
    09-03-2019, 01:45 PM Go to last post
  3. Pre-load on needle roller clutch

    Started by csendegeya, 08-30-2019 10:35 AM
    bearings, clutch
    • Replies: 1
    • Views: 816
    08-30-2019, 11:21 AM Go to last post
  4. Angle Iron Stress

    Started by komet99, 04-03-2012 10:48 PM
    • Replies: 9
    • Views: 69,867
    08-28-2019, 02:31 PM Go to last post
  5. Heat Exchanger Question

    Started by belachavbelachavchavchavchav, 08-22-2019 04:14 PM
    • Replies: 1
    • Views: 897
    08-23-2019, 09:27 AM Go to last post
  6. Uni project Help

    Started by Prialen08, 08-21-2019 10:41 AM
    design, jockey wheel
    • Replies: 0
    • Views: 770
    08-21-2019, 10:41 AM Go to last post
  7. Low Friction Fabrics

    Started by benjamin_banks, 05-01-2019 01:51 AM
    fabric, fashion, friction, material, science
    • Replies: 5
    • Views: 1,294
    08-15-2019, 11:41 AM Go to last post
  8. Ways to lessen wear caused by a steel fixture

    Started by harrisonczaj, 07-15-2019 11:47 AM
    fixture design, part wear, plastic coating
    • Replies: 5
    • Views: 1,142
    08-15-2019, 11:38 AM Go to last post
  9. SolidWorks Stress Analysis question

    Started by thinds, 08-12-2019 11:50 AM
    • Replies: 2
    • Views: 685
    08-13-2019, 09:10 AM Go to last post
  10. Material "Slash sheet description"

    Started by sdicarlo, 07-31-2019 03:41 PM
    • Replies: 0
    • Views: 544
    07-31-2019, 03:41 PM Go to last post
  11. Question tolerances, machining and cost

    Started by Ayien, 01-17-2018 08:23 PM
    gd&t, tolerances
    • Replies: 5
    • Views: 1,347
    07-29-2019, 02:16 PM Go to last post
  12. Aluminum on plastic tolerance fit?

    Started by sebastian_thomas, 04-29-2018 03:05 PM
    • Replies: 1
    • Views: 1,074
    07-29-2019, 02:10 PM Go to last post
  13. Need for advice

    Started by boutheynamzoughui, 07-29-2019 05:40 AM
    • Replies: 1
    • Views: 561
    07-29-2019, 08:20 AM Go to last post
  14. Air tanks in parallel and series

    Started by rouncer81, 07-26-2019 06:04 PM
    • Replies: 2
    • Views: 612
    07-26-2019, 06:38 PM Go to last post
  15. Reference for Table

    Started by halstedj, 07-26-2019 01:06 AM
    reference, source, table, thermal properties
    • Replies: 1
    • Views: 579
    07-26-2019, 08:21 AM Go to last post
  16. Red face Plastics Shredder Design

    Started by ramadhankd, 07-20-2019 09:19 AM
    calculation, invention, mechanical design, plastic, recycle
    • Replies: 1
    • Views: 809
    07-20-2019, 05:27 PM Go to last post
  17. Confused Help Plz!!! Scissor Lift, need help.

    Started by jw102033, 07-05-2019 11:07 AM
    • Replies: 0
    • Views: 1,114
    07-05-2019, 11:07 AM Go to last post
    • Replies: 2
    • Views: 2,071
    06-18-2019, 01:16 PM Go to last post
    • Replies: 7
    • Views: 1,165
    06-13-2019, 05:40 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •