Page 1 of 76 1 2 3 11 51 ... LastLast
Threads 1 to 20 of 1505

Forum: Engineering and Design Main Forum | Engineers Edge Forums

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 03:46 PM
    • Replies: 10
    • Views: 9,243
    11-15-2018, 01:07 AM Go to last post
  1. transmission project

    Started by rreye102, 11-09-2019 05:21 PM
    • Replies: 0
    • Views: 75
    11-09-2019, 05:21 PM Go to last post
    • Replies: 2
    • Views: 115
    11-03-2019, 09:02 PM Go to last post
    • Replies: 2
    • Views: 152
    10-28-2019, 12:51 PM Go to last post
    • Replies: 0
    • Views: 107
    10-28-2019, 12:43 PM Go to last post
    • Replies: 3
    • Views: 226
    10-24-2019, 01:16 PM Go to last post
  2. Machinery's, Roark's Stress and Strain, etc.

    Started by Kelly Bramble, 10-10-2019 09:04 AM
    • Replies: 2
    • Views: 352
    10-11-2019, 04:48 AM Go to last post
    • Replies: 1
    • Views: 382
    10-07-2019, 02:07 PM Go to last post
    • Replies: 0
    • Views: 335
    10-04-2019, 07:16 AM Go to last post
  3. Motor and Gearbox Pairing

    Started by darrell_gray, 09-18-2019 02:39 AM
    • Replies: 2
    • Views: 577
    09-25-2019, 03:24 AM Go to last post
  4. Deflection and Stress of arm with an angle

    Started by Enchantedhorses, 09-23-2019 11:33 AM
    • Replies: 1
    • Views: 506
    09-23-2019, 09:42 PM Go to last post
  5. Tempered glass "burst" calculation

    Started by ezetom, 09-23-2019 10:54 AM
    • Replies: 0
    • Views: 375
    09-23-2019, 10:54 AM Go to last post
  6. Stainless steel floor drain

    Started by iamdemberedingtonsbodygaurd, 09-11-2019 11:48 AM
    • Replies: 4
    • Views: 861
    09-22-2019, 11:49 AM Go to last post
  7. Back yard jet engine?

    Started by iamramondreddington, 09-12-2019 08:46 AM
    • Replies: 1
    • Views: 715
    09-19-2019, 03:16 PM Go to last post
  8. Structural safe loading calculation

    Started by sdubey, 09-18-2019 10:36 PM
    • Replies: 1
    • Views: 532
    09-19-2019, 05:13 AM Go to last post
    • Replies: 1
    • Views: 561
    09-16-2019, 03:29 PM Go to last post
  9. Lever arm design

    Started by lavdesesamajmeayakya, 08-30-2019 07:42 AM
    • Replies: 2
    • Views: 845
    09-05-2019, 03:18 PM Go to last post
  10. Pneumatic hammer prototype

    Started by cjccmc, 08-30-2019 04:23 PM
    • Replies: 1
    • Views: 790
    09-03-2019, 01:45 PM Go to last post
  11. Pre-load on needle roller clutch

    Started by csendegeya, 08-30-2019 10:35 AM
    bearings, clutch
    • Replies: 1
    • Views: 736
    08-30-2019, 11:21 AM Go to last post
  12. Angle Iron Stress

    Started by komet99, 04-03-2012 10:48 PM
    • Replies: 9
    • Views: 67,292
    08-28-2019, 02:31 PM Go to last post
  13. Heat Exchanger Question

    Started by belachavbelachavchavchavchav, 08-22-2019 04:14 PM
    • Replies: 1
    • Views: 815
    08-23-2019, 09:27 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •