Page 1 of 75 1 2 3 11 51 ... LastLast
Threads 1 to 20 of 1497

Forum: Engineering and Design Main Forum | Engineers Edge Forums

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 9,125
    11-15-2018, 12:07 AM Go to last post
  1. Deflection and Stress of arm with an angle

    Started by Enchantedhorses, 09-23-2019 10:33 AM
    • Replies: 0
    • Views: 2
    09-23-2019, 10:33 AM Go to last post
  2. Tempered glass "burst" calculation

    Started by ezetom, 09-23-2019 09:54 AM
    • Replies: 0
    • Views: 7
    09-23-2019, 09:54 AM Go to last post
  3. Stainless steel floor drain

    Started by iamdemberedingtonsbodygaurd, 09-11-2019 10:48 AM
    • Replies: 4
    • Views: 443
    09-22-2019, 10:49 AM Go to last post
  4. Back yard jet engine?

    Started by iamramondreddington, 09-12-2019 07:46 AM
    • Replies: 1
    • Views: 366
    09-19-2019, 02:16 PM Go to last post
  5. Structural safe loading calculation

    Started by sdubey, 09-18-2019 09:36 PM
    • Replies: 1
    • Views: 155
    09-19-2019, 04:13 AM Go to last post
  6. Motor and Gearbox Pairing

    Started by darrell_gray, 09-18-2019 01:39 AM
    • Replies: 1
    • Views: 190
    09-18-2019, 10:19 AM Go to last post
    • Replies: 1
    • Views: 234
    09-16-2019, 02:29 PM Go to last post
  7. Lever arm design

    Started by lavdesesamajmeayakya, 08-30-2019 06:42 AM
    • Replies: 2
    • Views: 736
    09-05-2019, 02:18 PM Go to last post
  8. Pneumatic hammer prototype

    Started by cjccmc, 08-30-2019 03:23 PM
    • Replies: 1
    • Views: 684
    09-03-2019, 12:45 PM Go to last post
  9. Pre-load on needle roller clutch

    Started by csendegeya, 08-30-2019 09:35 AM
    bearings, clutch
    • Replies: 1
    • Views: 655
    08-30-2019, 10:21 AM Go to last post
  10. Angle Iron Stress

    Started by komet99, 04-03-2012 09:48 PM
    • Replies: 9
    • Views: 66,048
    08-28-2019, 01:31 PM Go to last post
  11. Heat Exchanger Question

    Started by belachavbelachavchavchavchav, 08-22-2019 03:14 PM
    • Replies: 1
    • Views: 743
    08-23-2019, 08:27 AM Go to last post
  12. Uni project Help

    Started by Prialen08, 08-21-2019 09:41 AM
    design, jockey wheel
    • Replies: 0
    • Views: 638
    08-21-2019, 09:41 AM Go to last post
  13. Low Friction Fabrics

    Started by benjamin_banks, 05-01-2019 12:51 AM
    fabric, fashion, friction, material, science
    • Replies: 5
    • Views: 1,123
    08-15-2019, 10:41 AM Go to last post
  14. Ways to lessen wear caused by a steel fixture

    Started by harrisonczaj, 07-15-2019 10:47 AM
    fixture design, part wear, plastic coating
    • Replies: 5
    • Views: 914
    08-15-2019, 10:38 AM Go to last post
  15. SolidWorks Stress Analysis question

    Started by thinds, 08-12-2019 10:50 AM
    • Replies: 2
    • Views: 531
    08-13-2019, 08:10 AM Go to last post
  16. Material "Slash sheet description"

    Started by sdicarlo, 07-31-2019 02:41 PM
    • Replies: 0
    • Views: 397
    07-31-2019, 02:41 PM Go to last post
  17. Question tolerances, machining and cost

    Started by Ayien, 01-17-2018 07:23 PM
    gd&t, tolerances
    • Replies: 5
    • Views: 1,173
    07-29-2019, 01:16 PM Go to last post
  18. Aluminum on plastic tolerance fit?

    Started by sebastian_thomas, 04-29-2018 02:05 PM
    • Replies: 1
    • Views: 958
    07-29-2019, 01:10 PM Go to last post
  19. Need for advice

    Started by boutheynamzoughui, 07-29-2019 04:40 AM
    • Replies: 1
    • Views: 432
    07-29-2019, 07:20 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •