Page 1 of 76 1 2 3 11 51 ... LastLast
Threads 1 to 20 of 1507

Forum: Engineering and Design Main Forum | Engineers Edge Forums

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 03:46 PM
    • Replies: 10
    • Views: 9,258
    11-15-2018, 01:07 AM Go to last post
  1. No. of Holes

    Started by ahmed_shawki, 11-20-2019 03:15 AM
    • Replies: 1
    • Views: 22
    11-20-2019, 12:53 PM Go to last post
  2. Concentric Rings with constraints

    Started by flint59, 11-15-2019 05:24 PM
    seg
    • Replies: 0
    • Views: 53
    11-15-2019, 05:24 PM Go to last post
  3. transmission project

    Started by rreye102, 11-09-2019 05:21 PM
    • Replies: 0
    • Views: 164
    11-09-2019, 05:21 PM Go to last post
    • Replies: 2
    • Views: 170
    11-03-2019, 09:02 PM Go to last post
    • Replies: 2
    • Views: 217
    10-28-2019, 12:51 PM Go to last post
    • Replies: 0
    • Views: 163
    10-28-2019, 12:43 PM Go to last post
    • Replies: 3
    • Views: 354
    10-24-2019, 01:16 PM Go to last post
  4. Machinery's, Roark's Stress and Strain, etc.

    Started by Kelly Bramble, 10-10-2019 09:04 AM
    • Replies: 2
    • Views: 386
    10-11-2019, 04:48 AM Go to last post
    • Replies: 1
    • Views: 415
    10-07-2019, 02:07 PM Go to last post
    • Replies: 0
    • Views: 360
    10-04-2019, 07:16 AM Go to last post
  5. Motor and Gearbox Pairing

    Started by darrell_gray, 09-18-2019 02:39 AM
    • Replies: 2
    • Views: 604
    09-25-2019, 03:24 AM Go to last post
  6. Deflection and Stress of arm with an angle

    Started by Enchantedhorses, 09-23-2019 11:33 AM
    • Replies: 1
    • Views: 526
    09-23-2019, 09:42 PM Go to last post
  7. Tempered glass "burst" calculation

    Started by ezetom, 09-23-2019 10:54 AM
    • Replies: 0
    • Views: 397
    09-23-2019, 10:54 AM Go to last post
  8. Stainless steel floor drain

    Started by iamdemberedingtonsbodygaurd, 09-11-2019 11:48 AM
    • Replies: 4
    • Views: 880
    09-22-2019, 11:49 AM Go to last post
  9. Back yard jet engine?

    Started by iamramondreddington, 09-12-2019 08:46 AM
    • Replies: 1
    • Views: 728
    09-19-2019, 03:16 PM Go to last post
  10. Structural safe loading calculation

    Started by sdubey, 09-18-2019 10:36 PM
    • Replies: 1
    • Views: 548
    09-19-2019, 05:13 AM Go to last post
    • Replies: 1
    • Views: 573
    09-16-2019, 03:29 PM Go to last post
  11. Lever arm design

    Started by lavdesesamajmeayakya, 08-30-2019 07:42 AM
    • Replies: 2
    • Views: 855
    09-05-2019, 03:18 PM Go to last post
  12. Pneumatic hammer prototype

    Started by cjccmc, 08-30-2019 04:23 PM
    • Replies: 1
    • Views: 796
    09-03-2019, 01:45 PM Go to last post
  13. Pre-load on needle roller clutch

    Started by csendegeya, 08-30-2019 10:35 AM
    bearings, clutch
    • Replies: 1
    • Views: 743
    08-30-2019, 11:21 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •