Page 3 of 18 FirstFirst 1 2 3 4 5 13 ... LastLast
Threads 41 to 60 of 344

Forum: Dimensioning Tolerancing GD&T Discussion Forum | GD&T Training

Geometric dimensioning and tolerancing, limit tolerancing, drafting practices, GD&T, ASME Y14.5, GD&T training topics. GD&T Training

  1. Sticky Thread Sticky: ASME Y14.5-2009, Geometric Boundaries II GD&T Reference Book

    Started by administrator, 03-30-2014 02:41 PM
    • Replies: 2
    • Views: 17,556
    brianjonesengineer
    10-24-2020, 05:21 PM Go to last post

  2. Sticky Thread Sticky: GD&T Training ASME and ISO Standard Onsite

    Started by administrator, 03-30-2014 02:42 PM
    • Replies: 0
    • Views: 12,411
    administrator
    03-30-2014, 02:42 PM Go to last post

  1. Tolerances in Reference Dimension?

    Started by accentdesign, 03-16-2015 01:19 PM
    • Replies: 2
    • Views: 8,148
    accentdesign
    03-16-2015, 02:16 PM Go to last post

  2. Angle Basic Dimension

    Started by J.Powell, 11-12-2015 03:22 PM
    3 Attachment(s)
    • Replies: 7
    • Views: 8,127
    JFleck
    11-17-2015, 09:29 AM Go to last post

  3. What is the correct way to tolerance this True Position callout on a bolt hole circle

    Started by Paul Sarrach, 06-04-2015 07:39 AM
    1 Attachment(s)
    • Replies: 10
    • Views: 8,076
    Belanger
    06-05-2015, 08:47 PM Go to last post

  4. Roughness Rt Rzmax

    Started by cammarasana123, 10-06-2015 05:14 AM
    • Replies: 2
    • Views: 7,930
    cammarasana123
    10-08-2015, 09:48 AM Go to last post

  5. Datums on drawings

    Started by Dominguez Mexico, 08-11-2011 05:20 PM
    • Replies: 1
    • Views: 7,899
    Kelly_Bramble
    08-11-2011, 07:33 PM Go to last post

  6. Aluminum Pulley and Steel C3 bearing

    Started by trutech, 09-20-2012 01:58 PM
    • Replies: 13
    • Views: 7,886
    jboggs
    09-28-2012, 09:58 AM Go to last post

  7. A Level engineering help???

    Started by Aaron9890, 11-29-2011 05:36 AM
    a-level, gd&t, report..
    • Replies: 10
    • Views: 7,877
    Matthijs Heerschap
    01-23-2012, 07:56 AM Go to last post

  8. Welcome Hole Pattern with GD&T

    Started by gray_beard, 03-19-2018 06:56 PM
    calculation, datum, gd&t question, hole pattern, positional tolerance 4 Attachment(s)
    • Replies: 10
    • Views: 7,835
    Kelly_Bramble
    03-21-2018, 04:37 PM Go to last post

  9. Designing Go/No Go Fixture

    Started by wglipscomb, 01-26-2015 07:59 AM
    1 Attachment(s)
    • Replies: 6
    • Views: 7,763
    wglipscomb
    02-09-2015, 01:36 PM Go to last post

  10. True Position callout

    Started by joshmxz, 12-10-2012 02:49 PM
    • Replies: 3
    • Views: 7,683
    RWOLFEJR
    12-11-2012, 10:08 AM Go to last post

  11. Position to a keyway

    Started by JFleck, 10-16-2015 11:01 AM
    keyway, position 2 Attachment(s)
    • Replies: 6
    • Views: 7,656
    JFleck
    10-19-2015, 08:22 AM Go to last post

  12. torque vs thread engagement

    Started by muzaffaralkaff, 12-17-2013 03:16 AM
    thread engagement, torque apply 1 Attachment(s)
    • Replies: 4
    • Views: 7,575
    JAlberts
    12-17-2013, 10:54 PM Go to last post

  13. Overriding the Envelope Requirement in ISO GPS

    Started by dlloyd, 03-07-2012 11:16 AM
    • Replies: 1
    • Views: 7,526
    Kelly_Bramble
    03-09-2012, 09:00 AM Go to last post

  14. Callout for hole pattern on variable thickness

    Started by mbanerj, 07-06-2012 07:45 AM
    1 Attachment(s)
    • Replies: 7
    • Views: 7,349
    PinkertonD
    07-09-2012, 12:15 PM Go to last post

  15. GD&T Composite Feature Control Frame

    Started by quality_auditor, 12-28-2016 11:33 AM
    1 Attachment(s)
    • Replies: 7
    • Views: 7,348
    Cragyon
    01-06-2017, 11:44 AM Go to last post

  16. Where in Y14.5M is Third-Angle Projection identified as the default?

    Started by jerrymcmurphy, 12-28-2016 10:50 AM
    • Replies: 1
    • Views: 7,249
    Kelly_Bramble
    12-28-2016, 10:05 PM Go to last post

  17. re.position tolerance datum callout doubt

    Started by usnambur, 05-05-2011 09:50 AM
    • Replies: 2
    • Views: 7,119
    Belanger
    05-26-2011, 07:07 PM Go to last post

  18. GD&T Is this dimension ±.002 or .002 Max?

    Started by wbukovec, 08-01-2017 10:51 AM
    1 Attachment(s)
    • Replies: 1
    • Views: 7,098
    Kelly_Bramble
    08-01-2017, 11:10 AM Go to last post

  19. Using Square Symbol on a square hole pattern

    Started by bhollehday, 01-21-2020 04:00 PM
    • Replies: 2
    • Views: 7,001
    jboggs
    01-22-2020, 07:12 AM Go to last post

  20. Line to Line Fit Between Hole and Pin

    Started by wayne@expmachine.com, 02-13-2015 09:15 AM
    • Replies: 1
    • Views: 6,992
    Kelly_Bramble
    02-13-2015, 09:34 AM Go to last post
Page 3 of 18 FirstFirst 1 2 3 4 5 13 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules