Page 1 of 14 1 2 3 11 ... LastLast
Threads 1 to 20 of 280

Forum: Dimensioning Tolerancing GD&T Discussion Forum | GD&T Training

Geometric dimensioning and tolerancing, limit tolerancing, drafting practices, GD&T, ASME Y14.5, GD&T training topics. GD&T Training

    • Replies: 1
    • Views: 5,885
    04-26-2018, 12:25 AM Go to last post
  1. Sticky Thread Sticky: GD&T Training ASME and ISO Standard Onsite

    Started by administrator, 03-30-2014 02:42 PM
    • Replies: 0
    • Views: 4,475
    03-30-2014, 02:42 PM Go to last post
    • Replies: 1
    • Views: 41
    03-28-2020, 07:49 AM Go to last post
  1. ISO hole size tolerance

    Started by mark_kaltenborn, 03-20-2020 05:47 PM
    • Replies: 2
    • Views: 76
    03-23-2020, 08:39 AM Go to last post
    • Replies: 1
    • Views: 178
    03-05-2020, 12:10 AM Go to last post
  2. Using Square Symbol on a square hole pattern

    Started by bhollehday, 01-21-2020 04:00 PM
    • Replies: 2
    • Views: 400
    01-22-2020, 07:12 AM Go to last post
  3. I need help

    Started by mtpinnc, 01-15-2020 10:34 PM
    • Replies: 1
    • Views: 304
    01-16-2020, 07:42 AM Go to last post
  4. Economics / Cost of Applying GD&T

    Started by gioiosa, 01-06-2020 09:20 AM
    design, dimensioning, economics, gd&t, inspection
    • Replies: 3
    • Views: 355
    01-08-2020, 07:17 AM Go to last post
    • Replies: 3
    • Views: 347
    11-30-2019, 08:11 AM Go to last post
  5. Trends in Trainings on Engineering Standards

    Started by anoop_gupta, 10-26-2019 05:48 AM
    • Replies: 11
    • Views: 886
    10-29-2019, 12:05 PM Go to last post
  6. GD&T floating Fastener Formula question

    Started by james_kashuba, 09-25-2019 09:09 AM
    • Replies: 2
    • Views: 815
    09-25-2019, 10:21 AM Go to last post
  7. Basic or not?

    Started by brad_winesett, 09-19-2019 10:59 AM
    • Replies: 2
    • Views: 715
    09-19-2019, 12:50 PM Go to last post
    • Replies: 1
    • Views: 890
    09-11-2019, 01:50 PM Go to last post
  8. Position tolerance with circularity

    Started by brad_winesett, 09-09-2019 12:37 PM
    • Replies: 4
    • Views: 853
    09-09-2019, 03:19 PM Go to last post
  9. Is my tolerance stackup correct?

    Started by hsheldon, 09-04-2019 12:34 AM
    • Replies: 10
    • Views: 1,047
    09-05-2019, 02:13 PM Go to last post
  10. Referencing .STEP file as Basic Geometry

    Started by bosskomailchaiye, 08-30-2019 06:48 AM
    • Replies: 1
    • Views: 915
    08-30-2019, 08:35 AM Go to last post
    • Replies: 3
    • Views: 957
    07-29-2019, 10:20 AM Go to last post
  11. Question about tolerances

    Started by ionut_eduard, 06-20-2019 03:10 PM
    • Replies: 4
    • Views: 1,433
    06-21-2019, 03:43 PM Go to last post
  12. How calculate tol position datums mmc

    Started by jposadag, 06-05-2019 11:59 AM
    • Replies: 1
    • Views: 1,205
    06-05-2019, 12:51 PM Go to last post
  13. Position on coaxial features

    Started by steve_lopez, 06-05-2019 06:17 AM
    • Replies: 5
    • Views: 1,123
    06-05-2019, 11:41 AM Go to last post
    • Replies: 7
    • Views: 2,116
    06-03-2019, 08:24 AM Go to last post
    • Replies: 4
    • Views: 2,059
    05-20-2019, 07:45 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •