Page 3 of 5 FirstFirst 1 2 3 4 5 LastLast
Threads 41 to 60 of 93

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. European steels to ASTM

    Started by Bill M, 05-10-2011 03:13 PM
    • Replies: 1
    • Views: 6,971
    05-11-2011, 07:40 AM Go to last post
  2. reduction of motor torque

    Started by axt, 08-05-2011 03:41 PM
    • Replies: 1
    • Views: 5,122
    08-09-2011, 06:26 AM Go to last post
  3. Nozzle to cut plate

    Started by Dominguez Mexico, 08-17-2011 02:53 PM
    • Replies: 1
    • Views: 5,254
    08-17-2011, 06:22 PM Go to last post
    • Replies: 1
    • Views: 10,546
    09-06-2011, 02:37 PM Go to last post
  4. ASCE7-05 Wind Load C&C

    Started by xezio, 06-20-2012 04:39 PM
    • Replies: 1
    • Views: 8,776
    06-22-2012, 07:19 AM Go to last post
  5. design standard for centrifugal pumps

    Started by amuletm, 07-12-2012 03:04 AM
    • Replies: 1
    • Views: 4,591
    07-12-2012, 09:17 AM Go to last post
  6. AN-40 Locknut Shaft Dimensions

    Started by bickeljm, 11-28-2012 11:00 AM
    • Replies: 1
    • Views: 5,629
    11-28-2012, 04:42 PM Go to last post
  7. Bridge design specifications

    Started by Kelly_Bramble, 04-25-2014 08:22 PM
    • Replies: 1
    • Views: 4,575
    12-04-2014, 02:15 AM Go to last post
  8. din 867 standard

    Started by tlbong, 12-01-2014 10:00 AM
    din 867
    • Replies: 1
    • Views: 6,781
    12-01-2014, 03:56 PM Go to last post
    • Replies: 1
    • Views: 4,027
    04-17-2015, 03:04 PM Go to last post
  9. EPDM RUBBER details

    Started by subrao.adkurkar, 05-06-2015 07:09 AM
    • Replies: 1
    • Views: 3,991
    05-06-2015, 07:17 AM Go to last post
  10. Full Requirements

    Started by 2dos, 08-17-2015 03:57 AM
    manufacturing, specification, standards
    • Replies: 1
    • Views: 4,695
    08-17-2015, 07:31 AM Go to last post
  11. SMOTE Codes for matlab

    Started by mehrdadm2n, 11-04-2015 01:52 AM
    • Replies: 1
    • Views: 5,673
    11-04-2015, 06:07 AM Go to last post
    • Replies: 1
    • Views: 4,924
    04-12-2016, 02:48 AM Go to last post
    • Replies: 1
    • Views: 5,120
    07-13-2018, 07:17 AM Go to last post
    • Replies: 1
    • Views: 4,561
    11-21-2016, 08:54 AM Go to last post
  12. AISC bending of flat plates

    Started by gusschmoll, 09-27-2019 11:18 AM
    • Replies: 1
    • Views: 8,015
    09-27-2019, 01:08 PM Go to last post
  13. Symmetry lines / Center lines

    Started by janlsing, 05-22-2020 04:33 AM
    • Replies: 1
    • Views: 4,289
    05-22-2020, 07:27 AM Go to last post
  14. set SI-units

    Started by fdejong, 02-24-2021 01:05 AM
    si-system, unit
    • Replies: 1
    • Views: 4,506
    02-24-2021, 07:24 AM Go to last post
  15. Document Management for Published Drawings

    Started by tstroh, 06-28-2022 10:13 AM
    • Replies: 1
    • Views: 5,247
    06-28-2022, 10:59 AM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •