Page 3 of 5 FirstFirst 1 2 3 4 5 LastLast
Threads 41 to 60 of 93

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. European steels to ASTM

    Started by Bill M, 05-10-2011 03:13 PM
    • Replies: 1
    • Views: 7,084
    RWOLFEJR
    05-11-2011, 07:40 AM Go to last post

  2. reduction of motor torque

    Started by axt, 08-05-2011 03:41 PM
    • Replies: 1
    • Views: 5,220
    jboggs
    08-09-2011, 06:26 AM Go to last post

  3. Nozzle to cut plate

    Started by Dominguez Mexico, 08-17-2011 02:53 PM
    • Replies: 1
    • Views: 5,361
    PinkertonD
    08-17-2011, 06:22 PM Go to last post

  4. ANSI/ASME Standards for Fasteners - Thread Length Inquiry

    Started by Chubbs, 09-06-2011 01:24 PM
    ansi, asme, fastener, length, standard 1 Attachment(s)
    • Replies: 1
    • Views: 10,673
    Kelly_Bramble
    09-06-2011, 02:37 PM Go to last post

  5. ASCE7-05 Wind Load C&C

    Started by xezio, 06-20-2012 04:39 PM
    • Replies: 1
    • Views: 8,889
    Kelly_Bramble
    06-22-2012, 07:19 AM Go to last post

  6. design standard for centrifugal pumps

    Started by amuletm, 07-12-2012 03:04 AM
    • Replies: 1
    • Views: 4,698
    PinkertonD
    07-12-2012, 09:17 AM Go to last post

  7. AN-40 Locknut Shaft Dimensions

    Started by bickeljm, 11-28-2012 11:00 AM
    • Replies: 1
    • Views: 5,723
    Kelly_Bramble
    11-28-2012, 04:42 PM Go to last post

  8. Bridge design specifications

    Started by Kelly_Bramble, 04-25-2014 08:22 PM
    1 Attachment(s)
    • Replies: 1
    • Views: 4,675
    jackieann000
    12-04-2014, 02:15 AM Go to last post

  9. din 867 standard

    Started by tlbong, 12-01-2014 10:00 AM
    din 867
    • Replies: 1
    • Views: 6,867
    Kelly_Bramble
    12-01-2014, 03:56 PM Go to last post

  10. Automated monitor and Control of agricultural greenhouse

    Started by Eugene Nsabimana, 04-16-2015 02:59 PM
    • Replies: 1
    • Views: 4,137
    jboggs
    04-17-2015, 03:04 PM Go to last post

  11. EPDM RUBBER details

    Started by subrao.adkurkar, 05-06-2015 07:09 AM
    1 Attachment(s)
    • Replies: 1
    • Views: 4,096
    Cragyon
    05-06-2015, 07:17 AM Go to last post

  12. Full Requirements

    Started by 2dos, 08-17-2015 03:57 AM
    manufacturing, specification, standards
    • Replies: 1
    • Views: 4,807
    Kelly_Bramble
    08-17-2015, 07:31 AM Go to last post

  13. SMOTE Codes for matlab

    Started by mehrdadm2n, 11-04-2015 01:52 AM
    • Replies: 1
    • Views: 5,778
    Kelly_Bramble
    11-04-2015, 06:07 AM Go to last post

  14. Stress Analysis of Chilled Water Under ground piping using Intergraph Caesar II

    Started by ppengg, 04-11-2016 01:40 PM
    chilled, hdpe, underground, water pipe
    • Replies: 1
    • Views: 5,071
    Cake of Doom
    04-12-2016, 02:48 AM Go to last post

  15. Safety Standard for polymeric materials used in automotive electronics

    Started by andrew_templeton, 10-13-2016 02:59 PM
    • Replies: 1
    • Views: 5,425
    jamessmith00444
    07-13-2018, 07:17 AM Go to last post

  16. Vintage Military Aerospace Material Specifications

    Started by jeromy, 11-21-2016 08:29 AM
    aerospace, aviation, materials, specifications 1 Attachment(s)
    • Replies: 1
    • Views: 4,736
    Kelly_Bramble
    11-21-2016, 08:54 AM Go to last post

  17. AISC bending of flat plates

    Started by gusschmoll, 09-27-2019 11:18 AM
    • Replies: 1
    • Views: 8,384
    gusschmoll
    09-27-2019, 01:08 PM Go to last post

  18. Symmetry lines / Center lines

    Started by janlsing, 05-22-2020 04:33 AM
    • Replies: 1
    • Views: 4,578
    Kelly_Bramble
    05-22-2020, 07:27 AM Go to last post

  19. set SI-units

    Started by fdejong, 02-24-2021 01:05 AM
    si-system, unit
    • Replies: 1
    • Views: 4,793
    administrator
    02-24-2021, 07:24 AM Go to last post

  20. Document Management for Published Drawings

    Started by tstroh, 06-28-2022 10:13 AM
    • Replies: 1
    • Views: 5,534
    Kelly_Bramble
    06-28-2022, 10:59 AM Go to last post
Page 3 of 5 FirstFirst 1 2 3 4 5 LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules