Page 4 of 5 FirstFirst ... 2 3 4 5 LastLast
Threads 61 to 80 of 93

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. Full Requirements

    Started by 2dos, 08-17-2015 03:57 AM
    manufacturing, specification, standards
    • Replies: 1
    • Views: 4,841
    Kelly_Bramble
    08-17-2015, 07:31 AM Go to last post

  2. SMOTE Codes for matlab

    Started by mehrdadm2n, 11-04-2015 01:52 AM
    • Replies: 1
    • Views: 5,813
    Kelly_Bramble
    11-04-2015, 06:07 AM Go to last post

  3. Standard and norm

    Started by bhdrsc, 12-19-2015 08:34 AM
    • Replies: 0
    • Views: 4,345
    bhdrsc
    12-19-2015, 08:34 AM Go to last post

  4. Normalisation of ISO Standard

    Started by bhdrsc, 12-19-2015 11:57 AM
    • Replies: 0
    • Views: 4,244
    bhdrsc
    12-19-2015, 11:57 AM Go to last post

  5. In house tolerance standards

    Started by MR Wolfdog, 09-06-2011 07:40 PM
    • Replies: 12
    • Views: 59,811
    Kelly_Bramble
    01-08-2016, 07:24 AM Go to last post

  6. :bash: EN 13445-3 for the design of subsea suction anchor?

    Started by billyolly, 02-18-2016 01:59 AM
    • Replies: 2
    • Views: 7,501
    billyolly
    02-18-2016, 05:11 PM Go to last post

  7. HELP! Intergraph Caesar II UG HDPE pipe stress analysis

    Started by ppengg, 04-11-2016 01:46 PM
    caesar ii, intergraph, ug piping
    • Replies: 0
    • Views: 6,431
    ppengg
    04-11-2016, 01:46 PM Go to last post

  8. Stress Analysis of Chilled Water Under ground piping using Intergraph Caesar II

    Started by ppengg, 04-11-2016 01:40 PM
    chilled, hdpe, underground, water pipe
    • Replies: 1
    • Views: 5,126
    Cake of Doom
    04-12-2016, 02:48 AM Go to last post

  9. ISO to ANSI conversion

    Started by lydiaai, 08-09-2016 02:15 AM
    ansi, conversion, iso
    • Replies: 0
    • Views: 6,840
    lydiaai
    08-09-2016, 02:15 AM Go to last post

  10. Common Train Air/Rolling Resistance Values

    Started by Tmalott, 10-19-2016 09:42 PM
    common values, resistance, trains
    • Replies: 4
    • Views: 4,407
    Cake of Doom
    10-25-2016, 04:12 AM Go to last post

  11. Vintage Military Aerospace Material Specifications

    Started by jeromy, 11-21-2016 08:29 AM
    aerospace, aviation, materials, specifications 1 Attachment(s)
    • Replies: 1
    • Views: 4,810
    Kelly_Bramble
    11-21-2016, 08:54 AM Go to last post

  12. AS/NZS 1170.2: action combination factor (Kc)

    Started by sarahxaviera, 10-13-2017 12:53 PM
    2 Attachment(s)
    • Replies: 0
    • Views: 7,289
    sarahxaviera
    10-13-2017, 12:53 PM Go to last post

  13. Confused Drawing projections - QUESTION

    Started by carlost, 07-04-2018 12:03 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 5,112
    carlost
    07-05-2018, 09:45 AM Go to last post

  14. Safety Standard for polymeric materials used in automotive electronics

    Started by andrew_templeton, 10-13-2016 02:59 PM
    • Replies: 1
    • Views: 5,516
    jamessmith00444
    07-13-2018, 07:17 AM Go to last post

  15. ASME Section Viii (no stamp) vessel operates below 15 psig

    Started by crspublic8, 07-14-2018 11:57 AM
    • Replies: 1
    • Views: 7,509
    Kelly_Bramble
    07-15-2018, 09:12 AM Go to last post

  16. Shraeder/Presta Cycle Tire Standards

    Started by richard_fox, 06-23-2018 02:30 AM
    2 Attachment(s)
    • Replies: 5
    • Views: 6,419
    petronextinternational
    01-24-2019, 11:41 PM Go to last post

  17. Driving vs. Driven Dimensions

    Started by kcampbe, 11-28-2016 03:42 PM
    • Replies: 5
    • Views: 15,190
    petronextinternational
    02-14-2019, 03:37 AM Go to last post

  18. ASME GDTP technician test

    Started by Andrew T, 05-09-2016 09:46 AM
    • Replies: 4
    • Views: 10,622
    petronextinternational
    02-14-2019, 03:38 AM Go to last post

  19. AISC bending of flat plates

    Started by gusschmoll, 09-27-2019 11:18 AM
    • Replies: 1
    • Views: 8,539
    gusschmoll
    09-27-2019, 01:08 PM Go to last post

  20. Symmetry lines / Center lines

    Started by janlsing, 05-22-2020 04:33 AM
    • Replies: 1
    • Views: 4,633
    Kelly_Bramble
    05-22-2020, 07:27 AM Go to last post
Page 4 of 5 FirstFirst ... 2 3 4 5 LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules