Page 1 of 5 1 2 3 ... LastLast
Threads 1 to 20 of 93

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. Aluminum specific weight

    Started by Dominguez Mexico, 06-14-2011 07:20 PM
    • Replies: 10
    • Views: 76,369
    CCR5600Design
    07-08-2011, 02:25 PM Go to last post

  2. In house tolerance standards

    Started by MR Wolfdog, 09-06-2011 07:40 PM
    • Replies: 12
    • Views: 60,006
    Kelly_Bramble
    01-08-2016, 07:24 AM Go to last post

  3. Engineering Drawings Standard for Black and White or Color?

    Started by hogpaw, 12-10-2013 07:43 AM
    • Replies: 9
    • Views: 26,654
    Solidworksguy
    11-17-2020, 10:25 AM Go to last post

  4. Driving vs. Driven Dimensions

    Started by kcampbe, 11-28-2016 03:42 PM
    • Replies: 5
    • Views: 15,628
    petronextinternational
    02-14-2019, 03:37 AM Go to last post

  5. Allowable Stress Design and Plastic Design, June 1, 1989

    Started by Dominguez Mexico, 07-28-2011 11:34 AM
    • Replies: 4
    • Views: 12,783
    Dominguez Mexico
    08-01-2011, 03:04 PM Go to last post

  6. ASME GDTP technician test

    Started by Andrew T, 05-09-2016 09:46 AM
    • Replies: 4
    • Views: 11,162
    petronextinternational
    02-14-2019, 03:38 AM Go to last post

  7. ANSI/ASME Standards for Fasteners - Thread Length Inquiry

    Started by Chubbs, 09-06-2011 01:24 PM
    ansi, asme, fastener, length, standard 1 Attachment(s)
    • Replies: 1
    • Views: 10,813
    Kelly_Bramble
    09-06-2011, 02:37 PM Go to last post

  8. DIN Standard

    Started by jayman, 02-28-2012 07:20 PM
    din standards
    • Replies: 3
    • Views: 10,722
    RWOLFEJR
    02-29-2012, 01:05 PM Go to last post

  9. material specification

    Started by mohit333, 04-14-2015 11:28 PM
    materials, standards, steel
    • Replies: 3
    • Views: 10,510
    jessicaherron9
    07-05-2021, 07:10 AM Go to last post

  10. ASTM Yield and Ulitimate Clarification

    Started by RWOLFEJR, 03-16-2012 10:11 AM
    • Replies: 2
    • Views: 10,343
    Kelly_Bramble
    03-18-2012, 08:32 AM Go to last post

  11. Post Parts List Standard.

    Started by paddyh, 11-30-2011 04:11 AM
    • Replies: 2
    • Views: 9,879
    paddyh
    11-30-2011, 07:36 AM Go to last post

  12. ASCE7-05 Wind Load C&C

    Started by xezio, 06-20-2012 04:39 PM
    • Replies: 1
    • Views: 8,991
    Kelly_Bramble
    06-22-2012, 07:19 AM Go to last post

  13. AISC bending of flat plates

    Started by gusschmoll, 09-27-2019 11:18 AM
    • Replies: 1
    • Views: 8,927
    gusschmoll
    09-27-2019, 01:08 PM Go to last post

  14. Effective Modulus ( BS 5950)

    Started by whblitz, 04-13-2011 04:14 AM
    • Replies: 4
    • Views: 8,245
    PinkertonD
    05-10-2011, 07:54 PM Go to last post

  15. Drawing Standard Practices

    Started by Macguyver, 03-06-2012 03:58 PM
    • Replies: 2
    • Views: 8,068
    Kelly_Bramble
    03-07-2012, 07:21 AM Go to last post

  16. Code standard for hole callout note formats

    Started by brad_winesett, 10-15-2020 10:49 AM
    1 Attachment(s)
    • Replies: 3
    • Views: 7,866
    Kelly_Bramble
    10-15-2020, 03:13 PM Go to last post

  17. ASME Section Viii (no stamp) vessel operates below 15 psig

    Started by crspublic8, 07-14-2018 11:57 AM
    • Replies: 1
    • Views: 7,766
    Kelly_Bramble
    07-15-2018, 09:12 AM Go to last post

  18. :bash: EN 13445-3 for the design of subsea suction anchor?

    Started by billyolly, 02-18-2016 01:59 AM
    • Replies: 2
    • Views: 7,672
    billyolly
    02-18-2016, 05:11 PM Go to last post

  19. Need Ventilation requirements and exepmtions

    Started by gilramirez716, 08-08-2020 05:45 PM
    cfm requirement, safety, ventilation requirements
    • Replies: 2
    • Views: 7,608
    gilramirez716
    08-09-2020, 03:04 PM Go to last post

  20. burrs on machined plastic gasket

    Started by dfike19380, 08-31-2011 10:58 AM
    • Replies: 4
    • Views: 7,558
    PinkertonD
    08-31-2011, 06:10 PM Go to last post
Page 1 of 5 1 2 3 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules