Page 1 of 5 1 2 3 ... LastLast
Threads 1 to 20 of 91

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. What's this paint defect standard?

    Started by mark_short, 12-09-2022 06:14 AM
    • Replies: 3
    • Views: 1,366
    12-12-2022, 03:42 AM Go to last post
  2. Document Management for Published Drawings

    Started by tstroh, 06-28-2022 11:13 AM
    • Replies: 1
    • Views: 2,936
    06-28-2022, 11:59 AM Go to last post
  3. EN grade vs. EN number

    Started by martin_jnsson, 12-18-2021 04:04 AM
    • Replies: 8
    • Views: 3,249
    12-23-2021, 03:33 AM Go to last post
  4. material specification

    Started by mohit333, 04-15-2015 12:28 AM
    materials, standards, steel
    • Replies: 3
    • Views: 7,666
    07-05-2021, 08:10 AM Go to last post
    • Replies: 5
    • Views: 2,057
    05-27-2021, 04:48 PM Go to last post
  5. Iso 14692 load cases combinations caesar ii

    Started by ahmedchalbi635, 04-03-2021 04:15 AM
    • Replies: 0
    • Views: 2,260
    04-03-2021, 04:15 AM Go to last post
  6. set SI-units

    Started by fdejong, 02-24-2021 02:05 AM
    si-system, unit
    • Replies: 1
    • Views: 2,289
    02-24-2021, 08:24 AM Go to last post
    • Replies: 9
    • Views: 21,471
    11-17-2020, 11:25 AM Go to last post
    • Replies: 3
    • Views: 4,138
    10-15-2020, 04:13 PM Go to last post
  7. Need Ventilation requirements and exepmtions

    Started by gilramirez716, 08-08-2020 06:45 PM
    cfm requirement, safety, ventilation requirements
    • Replies: 2
    • Views: 5,380
    08-09-2020, 04:04 PM Go to last post
  8. Temporary Works Test Rig Design Codes

    Started by luke_sheader, 07-09-2020 09:59 AM
    • Replies: 0
    • Views: 2,434
    07-09-2020, 09:59 AM Go to last post
  9. Symmetry lines / Center lines

    Started by janlsing, 05-22-2020 05:33 AM
    • Replies: 1
    • Views: 2,446
    05-22-2020, 08:27 AM Go to last post
  10. AISC bending of flat plates

    Started by gusschmoll, 09-27-2019 12:18 PM
    • Replies: 1
    • Views: 5,311
    09-27-2019, 02:08 PM Go to last post
  11. ASME GDTP technician test

    Started by Andrew T, 05-09-2016 10:46 AM
    • Replies: 4
    • Views: 7,658
    02-14-2019, 04:38 AM Go to last post
  12. Driving vs. Driven Dimensions

    Started by kcampbe, 11-28-2016 04:42 PM
    • Replies: 5
    • Views: 12,055
    02-14-2019, 04:37 AM Go to last post
  13. Shraeder/Presta Cycle Tire Standards

    Started by richard_fox, 06-23-2018 03:30 AM
    • Replies: 5
    • Views: 4,065
    01-25-2019, 12:41 AM Go to last post
    • Replies: 1
    • Views: 4,382
    07-15-2018, 10:12 AM Go to last post
    • Replies: 1
    • Views: 3,274
    07-13-2018, 08:17 AM Go to last post
  14. Confused Drawing projections - QUESTION

    Started by carlost, 07-04-2018 01:03 PM
    • Replies: 3
    • Views: 3,179
    07-05-2018, 10:45 AM Go to last post
    • Replies: 0
    • Views: 5,441
    10-13-2017, 01:53 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •