Page 1 of 5 1 2 3 ... LastLast
Threads 1 to 20 of 93

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. TELECOMMS MASTS : Guy rope strengths to TIA-222H

    Started by chris_johnson467, 12-15-2023 09:16 AM
    cable, guy, mast, strand, tia-222h
    • Replies: 0
    • Views: 1,842
    chris_johnson467
    12-15-2023, 09:16 AM Go to last post

  2. ASME Guided Study Classes

    Started by bryantsonnier, 06-12-2023 04:01 PM
    • Replies: 0
    • Views: 5,105
    bryantsonnier
    06-12-2023, 04:01 PM Go to last post

  3. What's this paint defect standard?

    Started by mark_short, 12-09-2022 05:14 AM
    1 Attachment(s)
    • Replies: 3
    • Views: 6,160
    mark_short
    12-12-2022, 02:42 AM Go to last post

  4. Document Management for Published Drawings

    Started by tstroh, 06-28-2022 10:13 AM
    • Replies: 1
    • Views: 5,579
    Kelly_Bramble
    06-28-2022, 10:59 AM Go to last post

  5. EN grade vs. EN number

    Started by martin_jnsson, 12-18-2021 03:04 AM
    1 Attachment(s)
    • Replies: 8
    • Views: 5,902
    martin_jnsson
    12-23-2021, 02:33 AM Go to last post

  6. material specification

    Started by mohit333, 04-14-2015 11:28 PM
    materials, standards, steel
    • Replies: 3
    • Views: 10,108
    jessicaherron9
    07-05-2021, 07:10 AM Go to last post

  7. Standard face to face tolerances on welded components.

    Started by bryantsonnier, 05-27-2021 08:57 AM
    • Replies: 5
    • Views: 4,772
    Kelly_Bramble
    05-27-2021, 03:48 PM Go to last post

  8. Iso 14692 load cases combinations caesar ii

    Started by ahmedchalbi635, 04-03-2021 03:15 AM
    • Replies: 0
    • Views: 4,592
    ahmedchalbi635
    04-03-2021, 03:15 AM Go to last post

  9. set SI-units

    Started by fdejong, 02-24-2021 01:05 AM
    si-system, unit
    • Replies: 1
    • Views: 4,854
    administrator
    02-24-2021, 07:24 AM Go to last post

  10. Engineering Drawings Standard for Black and White or Color?

    Started by hogpaw, 12-10-2013 07:43 AM
    • Replies: 9
    • Views: 26,225
    Solidworksguy
    11-17-2020, 10:25 AM Go to last post

  11. Code standard for hole callout note formats

    Started by brad_winesett, 10-15-2020 10:49 AM
    1 Attachment(s)
    • Replies: 3
    • Views: 7,696
    Kelly_Bramble
    10-15-2020, 03:13 PM Go to last post

  12. Need Ventilation requirements and exepmtions

    Started by gilramirez716, 08-08-2020 05:45 PM
    cfm requirement, safety, ventilation requirements
    • Replies: 2
    • Views: 7,420
    gilramirez716
    08-09-2020, 03:04 PM Go to last post

  13. Temporary Works Test Rig Design Codes

    Started by luke_sheader, 07-09-2020 08:59 AM
    • Replies: 0
    • Views: 4,518
    luke_sheader
    07-09-2020, 08:59 AM Go to last post

  14. Symmetry lines / Center lines

    Started by janlsing, 05-22-2020 04:33 AM
    • Replies: 1
    • Views: 4,640
    Kelly_Bramble
    05-22-2020, 07:27 AM Go to last post

  15. AISC bending of flat plates

    Started by gusschmoll, 09-27-2019 11:18 AM
    • Replies: 1
    • Views: 8,551
    gusschmoll
    09-27-2019, 01:08 PM Go to last post

  16. ASME GDTP technician test

    Started by Andrew T, 05-09-2016 09:46 AM
    • Replies: 4
    • Views: 10,639
    petronextinternational
    02-14-2019, 03:38 AM Go to last post

  17. Driving vs. Driven Dimensions

    Started by kcampbe, 11-28-2016 03:42 PM
    • Replies: 5
    • Views: 15,206
    petronextinternational
    02-14-2019, 03:37 AM Go to last post

  18. Shraeder/Presta Cycle Tire Standards

    Started by richard_fox, 06-23-2018 02:30 AM
    2 Attachment(s)
    • Replies: 5
    • Views: 6,430
    petronextinternational
    01-24-2019, 11:41 PM Go to last post

  19. ASME Section Viii (no stamp) vessel operates below 15 psig

    Started by crspublic8, 07-14-2018 11:57 AM
    • Replies: 1
    • Views: 7,514
    Kelly_Bramble
    07-15-2018, 09:12 AM Go to last post

  20. Safety Standard for polymeric materials used in automotive electronics

    Started by andrew_templeton, 10-13-2016 02:59 PM
    • Replies: 1
    • Views: 5,520
    jamessmith00444
    07-13-2018, 07:17 AM Go to last post
Page 1 of 5 1 2 3 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules