Page 10 of 30 FirstFirst ... 8 9 10 11 12 20 ... LastLast
Threads 181 to 200 of 597

Forum: Mechanical Engineering Forum

Mechanical Design, Mechanical Engineering and Design Engineering related forum topics.

  1. End stop for Air cylinder

    Started by GlennD, 02-13-2014 03:06 PM
    • Replies: 3
    • Views: 6,070
    GlennD
    02-18-2014, 06:57 PM Go to last post

  2. Molten Salt Hermetic Sealing without O-ring or Gasket

    Started by hglund, 04-26-2018 04:59 PM
    boron nitride, gasket, graphite, o-ring, sealing
    • Replies: 3
    • Views: 2,889
    hglund
    04-27-2018, 04:13 PM Go to last post

  3. Low friction ratchet mechanism

    Started by MattsInventions, 04-20-2016 11:48 PM
    bicycle, friction, ratchet, spin, wheel
    • Replies: 3
    • Views: 5,017
    Hudson
    05-03-2016, 10:15 PM Go to last post

  4. Confused Special pneumatic valve

    Started by vincent_goverse, 10-01-2018 07:00 AM
    brakes, failsafe, pneumatic, redundant, valve 1 Attachment(s)
    • Replies: 3
    • Views: 3,218
    Cragyon
    02-06-2020, 09:29 AM Go to last post

  5. Compressive strength of a square tube.

    Started by gmajewski, 12-15-2021 12:28 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 4,872
    Kelly_Bramble
    12-16-2021, 10:28 AM Go to last post

  6. Blind Rivet Clearance Hole

    Started by tabrake, 03-15-2018 12:04 PM
    • Replies: 2
    • Views: 5,641
    Kelly_Bramble
    03-15-2018, 05:58 PM Go to last post

  7. GRP pipe characteristics

    Started by walid, 04-16-2013 05:14 AM
    • Replies: 2
    • Views: 5,226
    PinkertonD
    04-16-2013, 10:43 AM Go to last post

  8. describe the angle of repose in conjunction with machine design???

    Started by lucky1369, 05-01-2013 04:30 PM
    • Replies: 2
    • Views: 5,239
    Kelly_Bramble
    05-02-2013, 07:18 AM Go to last post

  9. Oil flow through a gallery

    Started by csiddharthn, 05-31-2013 11:34 PM
    bend, engine, lubricant, oil temperature, turbulence
    • Replies: 2
    • Views: 4,512
    csiddharthn
    06-03-2013, 05:01 AM Go to last post

  10. Pressure fluctuations vs Temperature

    Started by csiddharthn, 05-31-2013 11:42 PM
    fluctuation, pressure, temperature
    • Replies: 2
    • Views: 4,052
    csiddharthn
    06-03-2013, 05:01 AM Go to last post

  11. syncronize/cutting drive between two gears

    Started by snipe, 08-24-2013 04:20 PM
    • Replies: 2
    • Views: 3,446
    snipe
    08-27-2013, 03:03 PM Go to last post

  12. Hydralic pump

    Started by rahulmohan, 08-28-2013 03:49 AM
    • Replies: 2
    • Views: 3,319
    rahulmohan
    08-28-2013, 09:52 AM Go to last post

  13. Help on Heat transfer

    Started by phaniteja333, 09-04-2013 10:45 PM
    • Replies: 2
    • Views: 3,128
    phaniteja333
    09-05-2013, 03:51 AM Go to last post

  14. Problem temperature refrigerator

    Started by onezhizami87, 04-02-2014 09:50 PM
    • Replies: 2
    • Views: 2,895
    Andrewsmith112
    05-27-2014, 04:39 AM Go to last post

  15. lifting davit

    Started by rzalinear, 05-15-2014 03:46 AM
    1 Attachment(s)
    • Replies: 2
    • Views: 3,406
    rzalinear
    05-29-2014, 11:12 PM Go to last post

  16. Space Race Materials

    Started by shaw600, 05-16-2014 03:14 PM
    fabric, materials, race, shuttle, space
    • Replies: 2
    • Views: 3,580
    Kelly_Bramble
    05-16-2014, 06:31 PM Go to last post

  17. Bolt Torque v's Bolt Grade

    Started by dalob, 05-29-2014 11:46 PM
    • Replies: 2
    • Views: 3,586
    Kelly_Bramble
    05-30-2014, 01:56 PM Go to last post

  18. Question Calculating Tolerances on a Part

    Started by Neoxana01, 03-02-2016 11:45 AM
    dimensioning, tolerance
    • Replies: 2
    • Views: 5,328
    cautruccg
    04-14-2016, 03:50 AM Go to last post

  19. Measure of Basic Dimension

    Started by pgbalage, 03-18-2016 04:41 AM
    • Replies: 2
    • Views: 3,924
    cautruccg
    04-14-2016, 03:48 AM Go to last post

  20. Compression fittings and ferrule compression

    Started by b5032574, 04-06-2018 02:39 PM
    bolted joints, clamping force, compression fitting, ferrule
    • Replies: 2
    • Views: 2,926
    b5032574
    04-09-2018, 09:53 AM Go to last post
Page 10 of 30 FirstFirst ... 8 9 10 11 12 20 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules