Search:

Type: Posts; User: Hudson

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    370

    A file or tiny grinder on a bottom edge would...

    A file or tiny grinder on a bottom edge would remove any plating and reveal the base material.
  2. You can inject steam heated water into the...

    You can inject steam heated water into the discharge side of the pump or perhaps use the steam alone to pump the water.

    steam engine boilers, especially on locomotives which did not recirculate...
  3. Replies
    4
    Views
    409

    Why not tolerance a wall thickness to the O.D....

    Why not tolerance a wall thickness to the O.D. that can be checked with a simple ball or tube micrometer instead of relying on CMM and inspection tables. Think like a machinist.
  4. Replies
    10
    Views
    623

    Do I see 'B' and 'C' datums as the edge of both a...

    Do I see 'B' and 'C' datums as the edge of both a 3" and an 8" square part? Then you call out parts to be centered?

    Why not make two bolt holes a common datum in the x & Y plane?
  5. Replies
    2
    Views
    722

    Sounds dangerous but, first determine if the...

    Sounds dangerous but, first determine if the floor can handle the load. If you have two 1 foot wide, seven foot long supports at the base and 21,000 lbs supported by them that's 1500 lbs/sq.ft if...
  6. Replies
    2
    Views
    446

    Consider a urethane adhesive for windshields. ...

    Consider a urethane adhesive for windshields.

    https://www.3m.com/3M/en_US/company-us/all-3m-products/~/3M-Auto-Glass-Urethane-Windshield-Adhesive/?N=5002385+3293242009&rt=rud
  7. Replies
    2
    Views
    825

    Are they multi-million dollar dies? Years ago,...

    Are they multi-million dollar dies? Years ago, when the earth was thought to be cooling, auto makers used a free machining, low melting alloy called Kirksite for fender dies.

    More recently,...
  8. You have a .002 cylindricity and a roundness call...

    You have a .002 cylindricity and a roundness call out. That seems like double dimensioning to me.

    Could you just call out a .005 cylindricity and a surface finish on the basic shaft diameter and...
  9. Look harder for 1" couplings. They should be...

    Look harder for 1" couplings. They should be less than a dollar for the PVC type.
  10. Replies
    5
    Views
    2,012

    .283 lbs/cubic inch

    .283 lbs/cubic inch
  11. Replies
    1
    Views
    553

    If you know the distance from one pivot to...

    If you know the distance from one pivot to another on the links, it is a simple triangle problem:


    With angle theta and the distance from the two base pivot points and the length of the link...
  12. Replies
    6
    Views
    950

    Take another look at the Parker catalog (fine...

    Take another look at the Parker catalog (fine folks they are) and see if you haven’t misread the volume as gallons when the actual figure is in liters (57).


    57L is more like 15 gallons or 2...
  13. Replies
    2
    Views
    439

    Much simpler to mold is a vortex spiral.

    Much simpler to mold is a vortex spiral.
  14. Replies
    6
    Views
    950

    Regarding hydraulics, you cannot compress a...

    Regarding hydraulics, you cannot compress a liquid so your accumulator piston must work against some sort of spring like compressed air or steel. So the real energy storage is in the spring.

    ...
  15. Replies
    10
    Views
    860

    Confront the vendor and ask about the change in...

    Confront the vendor and ask about the change in finish.
  16. Replies
    3
    Views
    822

    You might look at a stepper motor and ball screw...

    You might look at a stepper motor and ball screw configuration that would be positioned under the table to provide linear force.

    Look for a 400 mm travel length linear stepper motor on Amazon. ...
  17. Replies
    3
    Views
    822

    Most mechanism to accomplish this motion will...

    Most mechanism to accomplish this motion will require a gear reduction. Since we don't know the motor speed, friction etc. it is not possible to give you a direct answer.

    You want to move 300...
  18. Look at some existing designs for folding or...

    Look at some existing designs for folding or Pullman berths. Some are ceiling mount - some are wall mount. Also consider getting double duty out of another piece of furniture like a table or a...
  19. Replies
    5
    Views
    633

    If you recall, the deflection equation used a...

    If you recall, the deflection equation used a length cubed term. The difference between 42 cubed and 36 cubed is considerable.


    We are now looking for a tube with a section moment of...
  20. Replies
    5
    Views
    633

    Increasing the allowable deflection by 2X reduces...

    Increasing the allowable deflection by 2X reduces the moment of inertia required by .


    A 3” square tube with an 1/8” wall has a section moment of inertia of approximately 1.98 inches^4. A...
  21. Replies
    5
    Views
    633

    We don’t know quite enough to design a davit for...

    We don’t know quite enough to design a davit for you.


    What we can guess is that that 200 lbf end load can get a lot higher under sea if the dinghy fills with storm water and starts to...
  22. Replies
    6
    Views
    978

    117 N/mm2 is a stress level equivalent to 117 MPa...

    117 N/mm2 is a stress level equivalent to 117 MPa or approximately 17,000 psi.



    This rather low stress for a bolt. This might be based on the unusual thermal requirements of a fireproof...
  23. Replies
    6
    Views
    1,252

    Are you attaching this gusset by welding?

    Are you attaching this gusset by welding?
  24. Replies
    8
    Views
    713

    Go back and read Kelly's well stated comments on...

    Go back and read Kelly's well stated comments on profitability.
  25. Replies
    7
    Views
    469

    Why not use rectangular tubing?

    Why not use rectangular tubing?
Results 1 to 25 of 153
Page 1 of 7 1 2 3 4