Search:

Type: Posts; User: Kelly Bramble

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 33 minute(s) ago.

  1. Replies
    1
    Views
    32

    No, it does not matter. Depending on the...

    No, it does not matter. Depending on the standard you are utilizing either the circle U and the 0.0 to # offset tolerance to indicate inside or outside (See ASME Y14.5-2018) or an offset phantom...
  2. Free Body Diagram ...

    Free Body Diagram

    https://www.engineersedge.com/material_science/free_body_diagram_13073.htm
  3. Depending on the end item or technology - a...

    Depending on the end item or technology - a concept might be an ideal or an overview of what an end product of system might be. A preliminary design typically includes some analysis, more details...
  4. q appears to be a flow rate where on page 4 (q...

    q appears to be a flow rate where on page 4 (q / Q ) appears to be a flow rate ratio.

    The document in question should provide declaration for each variable.
  5. You can ask questions here. I am not sure...

    You can ask questions here.

    I am not sure you'll get an answer as very little SAP is discussed here.
  6. Есть ли у Tekla и SAP справочный форум? Вы...

    Есть ли у Tekla и SAP справочный форум?


    Вы должны там задавать вопросы.
  7. Немногие посетители здесь говорят или пишут...

    Немногие посетители здесь говорят или пишут по-русски. Возможно, вам придется пойти туда, где их больше.


    Я не могу ответить на твой вопрос
  8. Replies
    2
    Views
    302

    A Spectrum analyzer is just a modern...

    A Spectrum analyzer is just a modern Oscilloscope. You would need the relevant sensors that process whatever the radiation is.
  9. Replies
    4
    Views
    408

    I see you're a brand new member, did you have a...

    I see you're a brand new member, did you have a account back in 2009?


    1) Engineers Edge is more than just a discussion forum. Answers folks need are gradually being populated here and all over...
  10. Replies
    2
    Views
    325

    Similar, Ra = Roughness Average RMS =...

    Similar,

    Ra = Roughness Average

    RMS = Root Mean Square

    Math is different but get you similar.
  11. There is almost always a new supplier issue with...

    There is almost always a new supplier issue with existing tough-to-build parts.

    Chances are that existing suppliers have built fixtures or have worked a special process to build your end item. We...
  12. Also, consider that in some installation...

    Also, consider that in some installation applications a flex pipe (bellows or other) can allow for more generous tolerance specifications in the primary piping installation.
  13. Weldments are challenging to hold tight...

    Weldments are challenging to hold tight tolerances without fixtures, post machining etc. Distortions are common due to the extreme temperature variations at the weld affected zone (WAZ) during the...
  14. Replies
    1
    Views
    292

    See: ...

    See:

    https://www.engineersedge.com/beam_bending/beam_bending17.htm
  15. Replies
    4
    Views
    522

    Here's associated formulas and calculator for...

    Here's associated formulas and calculator for flywheel design:

    Flywheel Mass Size Design Equation and Calculator
  16. Replies
    4
    Views
    522

    No.... energy cannot be created from nothing.

    No.... energy cannot be created from nothing.
  17. Your calculations are statically indeterminate...

    Your calculations are statically indeterminate and ignore real world deflections. Moreover, structures are never build in perfect orientation nor are structural members perfect. Thus, some...
  18. Replies
    2
    Views
    1,273

    That's probably a UV Spraying Coating.

    That's probably a UV Spraying Coating.
  19. Replies
    2
    Views
    449

    A image would be helpful..

    A image would be helpful..
  20. Replies
    0
    Views
    435

    Animation How A Gearbox Works

    This animation shows how an automotive manual gearbox works.

    2587
  21. Storage system for storing rainwater and using it when needed

    Tank configuration with overflow.

    2586
  22. I would try an organization that specializes in...

    I would try an organization that specializes in engineering and design professionals for hire.

    Engineers Edge gets lots of internet traffic however I'm pretty sure you're not going to find much...
  23. All GD&T Tolerance boundaries are applied to the...

    All GD&T Tolerance boundaries are applied to the full depth, width and length of the feature.

    X and Y measurements you're referring to are simple 2-d measurements from a specified and established...
  24. No... I think this is the second question in a...

    No...

    I think this is the second question in a week regarding the interpretation and setup for measurement to datums. Position tolerance can be 2D in very thin cross sections like a .0005" shim...
  25. Replies
    1
    Views
    811

    If it's a surface - it can be a datum. This works...

    If it's a surface - it can be a datum. This works as defined. Datum C can be simulated with two collapsing surfaces that are parallel to the engineering drawing graphics as specified. A CMM would...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4