Search:

Type: Posts; User: Kelly Bramble

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    472

    Engineers Edge does have a Stress-Strain curve...

    Engineers Edge does have a Stress-Strain curve Approximation calculator based on the Ramburg-Osgood equations.

    Enter known data and the curve data points are calculated plotted and tabulated.
    ...
  2. Breakout a detail view and indicate the number of...

    Breakout a detail view and indicate the number of occurrences that geometry occurs. Using the same datum order of precedence indicates a simultaneous requirement.
  3. According to Solidworks, yes.. But know that you...

    According to Solidworks, yes.. But know that you need to understand the whole system requirements.

    See: https://www.solidworks.com/support/hardware-certification
  4. You need to study up on Mohr's Circle for plane...

    You need to study up on Mohr's Circle for plane stresses.

    Start here..
    https://www.engineersedge.com/material_science/mohrs-circle-stress-plane.htm
  5. Python is a programming language, Civil...

    Python is a programming language, Civil engineering is a field of practice in engineering.

    The programming language used in any application does not matter - the app functionality does.

    Pick a...
  6. Also, ASME Y14.5-2018, Paragraph 5.4. and ...

    Also, ASME Y14.5-2018, Paragraph 5.4.

    and

    ASME Y14.5M-1994, paragraph 2.4

    and

    ANSI Y14.5M-1982, paragraph 2.4
  7. ' ASME Y14.5-2009, Paragraph 2.4...

    '

    ASME Y14.5-2009, Paragraph 2.4 "Interpretation of Limits"

    2513

    This is very-very basic knowledge, your organization needs training ASAP.

    See:
  8. ASME, ISO or whatever... Tolerances are not...

    ASME, ISO or whatever...

    Tolerances are not rounded. Flatness .001 = .0010000000000000000000000000000000000..... infinity

    Your metrology equipment should be 10X more repeatable for imperial...
  9. I always wait a few months or one release before...

    I always wait a few months or one release before I upgrade any software.

    This avoids the challenges with bugs - I'm not interested nor have time to beta test software.
  10. I'm going to type text in the order I verify.. ...

    I'm going to type text in the order I verify..

    ASME Y14.5-2009, read the following:

    Most of section 1.7... specifically:

    1.7.5.1

    Section 1.8..
  11. Replies
    1
    Views
    513

    If beams are separate, spacing should be closer...

    If beams are separate, spacing should be closer and maximum loading is understood per beam, stress, deflection, code requirements calculated and compared to design requirements.

    If beams are...
  12. Replies
    6
    Views
    552

    All drafting practices including modern ASME and...

    All drafting practices including modern ASME and ISO specify that a blind hole starts from the surface which it is shown as non-hidden or by solid outlines.

    Engineering drawings should be created...
  13. Replies
    6
    Views
    552

    Given vague - limited information.. The line...

    Given vague - limited information..

    The line showing the center bolt circle should be a center line.

    On the 4 mm holes, what does "Full Dia" do? What else would the hole features be?
    ...
  14. Replies
    6
    Views
    552

    Third or first angle drawing? If drawing is...

    Third or first angle drawing?

    If drawing is declared as first angle projection - 4mm holes specification is correct.
  15. See: ...

    See:

    https://www.engineersedge.com/calculators/agma_worm_and_spur_gear_design_equations_and_calculators_15310.htm

    Which is per. industry standard ANSI/AGMA 6034-B92
  16. Replies
    5
    Views
    377

    I suspect that intent may have been that 1/3 of...

    I suspect that intent may have been that 1/3 of hole is to ensure drainage from the pipe due to condensation or water entering from the top.

    When placing posts in my part of the world it is wise...
  17. Replies
    5
    Views
    377

    I'm a little confused with your explanation. I...

    I'm a little confused with your explanation.

    I do wonder if there is a code that overrides the manufacturer requirements and is being enforced by the inspector?

    You should have a "why" ...
  18. Replies
    1
    Views
    308

    Defective pressure regulator? Would need a...

    Defective pressure regulator?

    Would need a system schematic to trouble shoot.
  19. Not sure how to take your statement - but...

    Not sure how to take your statement - but inventing a spline geometry is a waste of effort as well as unpatent-able..

    Also, while we're on the subject, don't waste time inventing the following:...
  20. Unknown size and I'm guessing 10N (2.25 lbf) is...

    Unknown size and I'm guessing 10N (2.25 lbf) is applied at the tooth? Without knowing the size of the coupler and where that force is being applied I'm guessing a bit.

    Torque is given in lb-in, or...
  21. To start... and the most important question for...

    To start... and the most important question for the moment, how much torque is the coupling seeing?
  22. Replies
    2
    Views
    1,642

    Sand cast, You sure? You would need...

    Sand cast, You sure? You would need approximately .050" (1.3mm) machining allowance.


    I suspect this is more of a die cast part.
  23. Replies
    9
    Views
    2,567

    I've seen tubes that were deep drawn and then...

    I've seen tubes that were deep drawn and then polished internally used for shock absorbers / McPherson Struts.

    Build or maybe find an existing tube diameter.
  24. Replies
    9
    Views
    2,567

    ID of pipe smaller than required on build then...

    ID of pipe smaller than required on build then drill/ream to size for accuracy and consistent cylindrical surface.
  25. The calculator delivers two stress calculation...

    The calculator delivers two stress calculation points, one at the support and one at a distance x from the support.

    Thus, there are two stress "s" calculations and two deflections "y". One at l...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4