Search:

Type: Posts; User: Kelly Bramble

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Also, you could Hardcoat Anodize per, MIL-A-8625...

    Also, you could Hardcoat Anodize per, MIL-A-8625 Type III which should help extend the life of the fixtures.
  2. Place a dimension from the edge (top and right...

    Place a dimension from the edge (top and right side maybe) to one of the holes or identify the width and height dimensions as datums.

    Thin is not an issue... though if the part distorts in the...
  3. Replies
    2
    Views
    37

    Good question – one that I have been looking at...

    Good question – one that I have been looking at for many years as Design for Manufacturing and Assembly trainer and consultant. I’ve visited the manufacturing floors of an unknown number of companies...
  4. No... unless you specify how the center line is...

    No... unless you specify how the center line is located on the part with dimensions and tolerances. Typically, this is done with datums.
  5. Regardless of the fixture structural members...

    Regardless of the fixture structural members materials (Aluminum, fiberglass, or whatever..) the features/parts on the fixturing tools that contact the features on the part or assembly should be...
  6. Replies
    1
    Views
    191

    Typically, 52110 chrome steel is used in bearing...

    Typically, 52110 chrome steel is used in bearing and bearing components.


    I'm sure you can thread the material though I doubt it is easy and I doubt you would have too much problems it if...
  7. "Can stainless be shaped like a car fender? " ...

    "Can stainless be shaped like a car fender? " Yes.
  8. Replies
    1
    Views
    280

    Try one of these: Ingenious Mechanisms I...

    Try one of these:


    Ingenious Mechanisms I
    IIngenious Mechanisms II
    Ingenious Mechanisms III
    Ingenious Mechanisms IV
  9. Replies
    1
    Views
    550

    See this: Heat Loss along an Insulated Pipe...

    See this: Heat Loss along an Insulated Pipe Equation and Calculator.
  10. Replies
    4
    Views
    814

    Note that according to ASME Y14.5-2009 and...

    Note that according to ASME Y14.5-2009 and previous dimensioning and tolerancing standards reference dimensions are not binding to quality.

    Moreover, reference dimensions are dimensions contained...
  11. Replies
    4
    Views
    814

    The 15 mm tolerance will be the default defined...

    The 15 mm tolerance will be the default defined on the engineering drawing. If there is not a default tolerance you will need one.
  12. See: Hole MMC Tolerance Calculator ...

    See:

    Hole MMC Tolerance Calculator

    https://www.engineersedge.com/calculators/mmc-size-geometric-tolerance.htm
  13. Replies
    5
    Views
    793

    By default, position location measurements should...

    By default, position location measurements should be made to the pitch diameter. Though you may get adequate measurement from the major diameter as well. To very the pitch diameter size and...
  14. For clarity on dimensioning a slot I was...

    For clarity on dimensioning a slot I was recommending that the op place the dimensions NORMAL to the slot feature not change the physical orientation of the slot feature. Though I do think the...
  15. They are just an led diode...

    They are just an led diode...
  16. Stepper motor mechanism and an electronics...

    Stepper motor mechanism and an electronics engineer.
  17. flexible neon blue light... Search for it

    flexible neon blue light... Search for it
  18. So, concrete is great in compression and poor in...

    So, concrete is great in compression and poor in tension. Which is why concrete includes steel rebar located towards the tension side in pavement.

    The op could fill the tubes with wood or another...
  19. You have an iron board... Sure, fill it with...

    You have an iron board... Sure, fill it with concrete though weight will increase. Be sure you have plenty footing that is wide.

    2297
  20. As an ASME certified Senior level GDTP...

    As an ASME certified Senior level GDTP professional since 1997 (Google me), and having wrote and published eight books on dimensioning and tolerancing - NO... A parallel dimension does not change...
  21. ? Placing the 8mm dimension parallel...

    ? Placing the 8mm dimension parallel (perpendicular to radius) with the length does not change the intent nor the specification - it is most correct per. ASME and ISO.

    See ASME Y14.5-2009,...
  22. Yes, the 8mm feature is drawn and dimensioned...

    Yes, the 8mm feature is drawn and dimensioned symmetrical about Datum B. Your 8 mm dimension should actually be placed parallel to the 8MM feature, or perpendicular to the end radius.
  23. Replies
    5
    Views
    1,759

    For b, see Hydrostatic Pressure vs Depth ->...

    For b, see Hydrostatic Pressure vs Depth -> https://www.engineersedge.com/fluid_flow/hydrostatic-pressure.htm

    Also,

    https://www.engineersedge.com/fluid_flow/relationship_depth_pressure.htm
    ...
  24. Replies
    5
    Views
    1,759

    The pressure along length h needs to be greater...

    The pressure along length h needs to be greater than the pressure along length b unless there is an external force (torque) applied to the mechanism.
  25. Replies
    3
    Views
    957

    What makes you think it "stick to skin strongly"?

    What makes you think it "stick to skin strongly"?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4