Search:

Type: Posts; User: Hudson

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    141

    I don't know who said it first but, Nothing ruins...

    I don't know who said it first but, Nothing ruins a good idea like a scale drawing.
  2. Replies
    13
    Views
    834

    Data taken from: Ameriti

    Data taken from: Ameriti
  3. search: "soil pressure"

    search: "soil pressure"
  4. Replies
    2
    Views
    713

    You have specified the functional dimension that...

    You have specified the functional dimension that you want. Looks fine to me.
  5. Replies
    1
    Views
    505

    I'm just speculating, by looking at the worm,...

    I'm just speculating, by looking at the worm, that the interference may have been caused by the worm not being extended far enough along the length of the shaft. The type of worm and worm wheel that...
  6. Replies
    13
    Views
    834

    Thermoset plastics are typically formed by...

    Thermoset plastics are typically formed by compression molding at temperature.

    If you are interested in a high temperature plastic that you can machine for prototypes, look at Dupont Vespel which...
  7. Replies
    13
    Views
    834

    Have you considered thermoset plastics?

    Have you considered thermoset plastics?
  8. Replies
    13
    Views
    834

    How hot does the part get? Can it be a burly...

    How hot does the part get? Can it be a burly engineered plastic?
  9. Replies
    13
    Views
    834

    Have you thought about a thread insert?

    Have you thought about a thread insert?
  10. Replies
    5
    Views
    739

    most threads are actually rolled. The threaded...

    most threads are actually rolled. The threaded section was probably about pitch diameter when the part was headed and then the threads rolled on that section. You are right about most being...
  11. Your 304 material appears to have be formed to...

    Your 304 material appears to have be formed to create the flange. The forming stresses and work hardening are not something that can be known to the forum viewers. Was the material annealed after...
  12. Replies
    5
    Views
    739

    Many threading dies have a gap that allows the...

    Many threading dies have a gap that allows the die to be closed a bit by the set screws that hold it into the die holder. Does your die holder allow this adjustment?
  13. Replies
    4
    Views
    1,002

    Span? 16' is about max span for a 2x10 check...

    Span? 16' is about max span for a 2x10 check the tables and the grade stamp on your joists. Some codes allow floor sheathing which is pretty thin and the deflection will vary with the cube of the...
  14. Replies
    2
    Views
    1,256

    I'm voting for taper lock split bushings and...

    I'm voting for taper lock split bushings and matching hub. You may not need the key depending upon the torque applied. They hold really well.
  15. Replies
    6
    Views
    905

    The indexer jboggs mentions is a good idea. Also...

    The indexer jboggs mentions is a good idea. Also investigate shot pins to position. The name Ferguson drive comes to mind as well.
  16. Replies
    6
    Views
    905

    Why do they have to be on a turn table? Or why...

    Why do they have to be on a turn table? Or why can't they be moved in a straight line? How accurate do they have to be for measurement?
  17. Replies
    3
    Views
    847

    likely done as a stamping.

    likely done as a stamping.
  18. Replies
    12
    Views
    3,617

    Did you look at drawn over mandrel tubing?...

    Did you look at drawn over mandrel tubing? (D.O.M.)
  19. Your rotary engine becomes a stationary engine. ...

    Your rotary engine becomes a stationary engine. The rotor must rotate to maintain the tips of the rotor in contact with the case as it the eccentric moves on the output shaft. The gears maintain...
  20. Replies
    3
    Views
    1,180

    If you are concerned about undercuts and using...

    If you are concerned about undercuts and using involute profiles, look into long and short addendums.
  21. Replies
    3
    Views
    1,180

    The term spur gear usually refers to a straight...

    The term spur gear usually refers to a straight (parallel to the axis of rotation) cut gear regardless of tooth geometry. This differentiates them from helical gears which have teeth cut at an angle...
  22. Replies
    8
    Views
    923

    There are lots of old wooden boats scrapped for...

    There are lots of old wooden boats scrapped for being rotted. My cheap self would look for something to salvage. However, the tiller has one big advantage in that you can control the throttle and...
  23. Replies
    9
    Views
    1,159

    Jboggs is correct, the electromagnetic clutch in...

    Jboggs is correct, the electromagnetic clutch in the gearbox is unusual.

    The first step in your redesign is to move the clutch to the input shaft on the exterior of the gearbox. The input shaft...
  24. Following up on Kelly's idea, look at overrun...

    Following up on Kelly's idea, look at overrun clutches and one way clutches.
  25. Your description is vague and the best...

    Your description is vague and the best engineering design cannot be made without a complete review of the design elements in your installation. So this cannot be a recommendation.

    However,...
Results 1 to 25 of 201
Page 1 of 9 1 2 3 4