Search:

Type: Posts; User: Kelly Bramble

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    6
    Views
    82

    I suspect that intent may have been that 1/3 of...

    I suspect that intent may have been that 1/3 of hole is to ensure drainage from the pipe due to condensation or water entering from the top.

    When placing posts in my part of the world it is wise...
  2. Replies
    6
    Views
    82

    I'm a little confused with your explanation. I...

    I'm a little confused with your explanation.

    I do wonder if there is a code that overrides the manufacturer requirements and is being enforced by the inspector?

    You should have a "why" ...
  3. Replies
    1
    Views
    76

    Defective pressure regulator? Would need a...

    Defective pressure regulator?

    Would need a system schematic to trouble shoot.
  4. Not sure how to take your statement - but...

    Not sure how to take your statement - but inventing a spline geometry is a waste of effort as well as unpatent-able..

    Also, while we're on the subject, don't waste time inventing the following:...
  5. Unknown size and I'm guessing 10N (2.25 lbf) is...

    Unknown size and I'm guessing 10N (2.25 lbf) is applied at the tooth? Without knowing the size of the coupler and where that force is being applied I'm guessing a bit.

    Torque is given in lb-in, or...
  6. To start... and the most important question for...

    To start... and the most important question for the moment, how much torque is the coupling seeing?
  7. Replies
    2
    Views
    1,445

    Sand cast, You sure? You would need...

    Sand cast, You sure? You would need approximately .050" (1.3mm) machining allowance.


    I suspect this is more of a die cast part.
  8. Replies
    9
    Views
    2,333

    I've seen tubes that were deep drawn and then...

    I've seen tubes that were deep drawn and then polished internally used for shock absorbers / McPherson Struts.

    Build or maybe find an existing tube diameter.
  9. Replies
    9
    Views
    2,333

    ID of pipe smaller than required on build then...

    ID of pipe smaller than required on build then drill/ream to size for accuracy and consistent cylindrical surface.
  10. The calculator delivers two stress calculation...

    The calculator delivers two stress calculation points, one at the support and one at a distance x from the support.

    Thus, there are two stress "s" calculations and two deflections "y". One at l...
  11. Doing an analysis without any engineering...

    Doing an analysis without any engineering training or education will be challenging. I do suggest that you determine the risk associated to yourself, end user and employer before proceeding.

    See:...
  12. The final functional test should reflect the way...

    The final functional test should reflect the way the strut is functionally used.
  13. Replies
    3
    Views
    3,149

    See: AGMA Worm and Spur Gwar Design Equations...

    See:

    AGMA Worm and Spur Gwar Design Equations and Calculator

    https://www.engineersedge.com/calculators/agma_worm_and_spur_gear_design_equations_and_calculators_15310.htm
  14. Look at the time that the torque is applied and...

    Look at the time that the torque is applied and any cyclic loading. Energy will be absorbed by the flexible shaft but eventually total input torque will be translated through the shaft.
  15. Replies
    1
    Views
    2,089

    Current, voltage and crosstalk requirements would...

    Current, voltage and crosstalk requirements would be you only concern. Possible solution.
  16. If this is a closed system pressured above that...

    If this is a closed system pressured above that produced by gravity then the pressure is the same everywhere except during flow.

    If it is a gravity system the system will vary with elevation.
    ...
  17. Replies
    4
    Views
    1,901

    Hydraulic accumulators are sized and pressured to...

    Hydraulic accumulators are sized and pressured to the system operational volumetric and pressure requirements. If you install an accumulator that operates at the wrong pressure charge and/or...
  18. Replies
    4
    Views
    1,901

    The Toyota part number is 4795030010 which also...

    The Toyota part number is 4795030010 which also fits the 4Runner and RAV4.

    Why would you not just go to a Toyota dealership and buy the OEM part?

    Toyota Parts Center Online sells them...
  19. Replies
    9
    Views
    979

    It has a tolerance when not produced at MMC size....

    It has a tolerance when not produced at MMC size. Ultimately, the value of this specification is that the are more size and as-manufactured position tolerances available for manufacturing.

    It's...
  20. Replies
    9
    Views
    979

    I agree in ~ general with your statement; however...

    I agree in ~ general with your statement; however engineering, manufacturing, quality and others whom must create or interpret an engineering drawing should have sufficient training and or experience...
  21. Where an arrow or a clear drafting association...

    Where an arrow or a clear drafting association with surface is given - that's the surface roughness required.

    For those surface roughness specifications within the brackets - contact the...
  22. Replies
    9
    Views
    979

    The MCC modifier means that at that specified...

    The MCC modifier means that at that specified size (Maximum Material Condition) which the smallest as-built allowed by tolerance for a hole feature or the largest allowed as-built by tolerance and...
  23. Replies
    9
    Views
    979

    If you had posted an image or exact details of...

    If you had posted an image or exact details of the position tolerance specification we could chart it out for you..

    Does the specification include a MMC modifier (Circle M) after the zero...
  24. The math is somewhat tedious, I recommend you use...

    The math is somewhat tedious, I recommend you use the 2D statics modeler on this website.

    https://www.engineersedge.com/calculators/statics-modeler/statics-2d-modeling.htm
  25. 3D Printer Troubleshooting and Repair

    I have 3D printer that recently had a control circuit board failure. After some trouble shooting I verified the Rambo 1.3L Z-Axis circuit was not functioning properly. Rambo boards are commonly used...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4