Search:

Type: Posts; User: Cake of Doom

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. So you need to check it for a combination of...

    So you need to check it for a combination of loads; both horizontal for bending and compression? Something also sounds a bit off about the information they have provided you. But anyways, as you have...
  2. Replies
    2
    Views
    1,960

    Have you tried looking at the snap settings...

    Have you tried looking at the snap settings configuration? I know it sounds a bit DUH! but it's usually the simplest things that give us the most trouble.
  3. It looks like a Lat/Long coordinate rather than...

    It looks like a Lat/Long coordinate rather than an E/N location which would give a latitude range of +90 to -90 and a longitude range of +180 to -180. Without seeing the drawing it's hard to guess at...
  4. Replies
    3
    Views
    966

    It's conductive adhesive gel. Similar to the...

    It's conductive adhesive gel. Similar to the stuff that's used with hospital electrodes.
  5. Replies
    4
    Views
    946

    Google (or preferred search engine) GlideWear....

    Google (or preferred search engine) GlideWear. They produce low friction fabrics for clothes, prosthetics, sports, etc.
  6. Replies
    4
    Views
    946

    Short answer: Yes. What is the intended...

    Short answer: Yes.

    What is the intended application?
  7. Replies
    7
    Views
    801

    Is it actual, worked examples you'd like?

    Is it actual, worked examples you'd like?
  8. Replies
    1
    Views
    410

    Depends on the size of the hole. If it's small,...

    Depends on the size of the hole. If it's small, say for some light load services, the local deflections may be negligible (10% or less of the beam depth ~). If it's a large hole, I'd look at the...
  9. Replies
    1
    Views
    915

    View Post

    It's available on Kindle for ~57, somewhere around $70 I think. To get it any cheaper as a physical/PDF copy, you'd probably have to step back by 5 or 6 editions.
  10. Replies
    2
    Views
    735

    On The First Day Of Christmas...

    The client gave to me
    A poorly constructed and eccentrically loaded foundation pad with bad ground conditions.

    Merry Chrimbo everyone.
  11. A deeper cover can be a good thing, especially if...

    A deeper cover can be a good thing, especially if the pads are to open to the elements. What measurement did they set any bottom and face cover out for? Not seeing any geotech reports, its hard to...
  12. Replies
    3
    Views
    1,075

    Because qualification is not equal to competence....

    Because qualification is not equal to competence. As demonstrated by every fresh graduate, ever. And yes; that included me.
  13. Better in what way? What is the end use of the...

    Better in what way? What is the end use of the material?
  14. Replies
    2
    Views
    761

    [grumpy voice] How I loathe and detest Excel...

    [grumpy voice] How I loathe and detest Excel [/grumpy voice]
  15. Replies
    5
    Views
    936

    ALL Mechanical Design?! I think the sun will...

    ALL Mechanical Design?! I think the sun will implode before you'll be able to learn all of it. What academic stage are you currently at?
  16. Replies
    6
    Views
    581

    Can you see anything else on it like "8.8", "M10"...

    Can you see anything else on it like "8.8", "M10" or "10.9", "M18" any other similar markings? If not, you have to try to contact the manufacturer and get them to provide you with more information.
  17. Replies
    2
    Views
    692

    The extension on those connector pins is...

    The extension on those connector pins is ridiculous! They must burn through tons of those just in factory assembly alone!
  18. Have you tried contacting any battle reenactment...

    Have you tried contacting any battle reenactment groups/forums? Going by the octagonal barrel, I'd suggest American groups. In time period you stated Europe was still using smooth bore flintlocks for...
  19. Do you have enough material to run practical...

    Do you have enough material to run practical tests?
  20. Are you sure you've entered the right values?...

    Are you sure you've entered the right values? With 100 kg as a mid-span load with 3.5 m length, I get 0.16 mm deflection. That's not including self weight of section and and decking.
  21. As no loads have been given, it's impossible to...

    As no loads have been given, it's impossible to even guess what the welds will be subject to. If it's a compression load, the plates should be OK but the welds will be subject to bending and shear...
  22. Replies
    5
    Views
    778

    It sounds like Galvalume has probably been...

    It sounds like Galvalume has probably been designed for use with Metsec or other proprietary type purlin systems. Sorry you had to rip out your new roof.
  23. Replies
    2
    Views
    540

    Wouldn't this turn into a tangential force,...

    Wouldn't this turn into a tangential force, rather than linear?
  24. Replies
    1
    Views
    527

    Good work!

    Good work!
  25. Replies
    1
    Views
    3,034

    I love pictures like this. The old liners, luxury...

    I love pictures like this. The old liners, luxury train carriages etc. We just don’t seem to have that level of class anymore.
Results 1 to 25 of 431
Page 1 of 18 1 2 3 4