Search:

Type: Posts; User: YorkshireDave

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    714

    In the absence of doing anything practical such...

    In the absence of doing anything practical such as Hudson's suggestion, I'd personally focus on the colour. It's that that gives it away for me. Stainless is very rarely chrome plated so simply...
  2. Thank you for the idea. For what YOU have...

    Thank you for the idea. For what YOU have described, it's a great possibility.

    I fear however that I have inadvertently mislead you all so time to be a little clearer.

    I am working on a...
  3. 2338 Drawing attached. Hopefully it now makes...

    2338

    Drawing attached. Hopefully it now makes more sense. Apologies for the confusion, thought everyone had crystal balls these days :-)

    The 8mm dia shaft is added to the 12mm shaft on a maint...
  4. Replies
    3
    Views
    1,250

    They do it through light pipes. The LEDs are on a...

    They do it through light pipes. The LEDs are on a board and the perspex, or whatever, light pipe is shaped so it gathers the light and presents it at the end as you see.
  5. Small thread advice - anti loosening

    Hi

    First off I have searched. The searching has made me fully realise (vs only suspecting) that this subject is not simple but that I want to learn, to understand. Thanks.

    I have a small...
  6. Hi Hudson Thank you so much. I have managed...

    Hi Hudson

    Thank you so much.

    I have managed to find DIN 5481 which kinda feels right. From further reading I understand one calculates the pin dia as it must touch at some 'magical' point (or...
  7. Many thanks for those. I had found some not...

    Many thanks for those. I had found some not others.

    Confession time. I can't make head nor tail of it all. From what I can see, that seems to be for 'proper' splines, splines designed to transmit...
  8. 'simple' spline calculation help pls

    Would someone be kind enough to point me to where I might be able to learn how to specify some simple splines?

    Let me expand. I need to create a series of spindles for tap (faucet) cartridges (the...
  9. Replies
    8
    Views
    2,245

    It's not complicated. However one part must be...

    It's not complicated. However one part must be changeable. Hence the join.
  10. There is one other difference to consider too....

    There is one other difference to consider too. Switchgear is designed to be regularly operated whereas circuit breakers are not.
  11. Replies
    8
    Views
    2,245

    I'm not doing anything 'special' I agree. Tap in...

    I'm not doing anything 'special' I agree. Tap in this instance is your faucet, so the forces involved are turning and typical of those involved in the daily use of a faucet.

    As I'm looking to...
  12. Replies
    8
    Views
    2,245

    Thank you peeps. COD. Hmm. I have to be...

    Thank you peeps.

    COD. Hmm. I have to be careful describing the use due to wanting to protect what I'm doing. Suffice to say, the side with the splines on will have a tap head attached and the...
  13. Replies
    8
    Views
    2,245

    Joining two brass components - advice?

    I have a 8mm long, 10mm round brass shaft (A) to which I need to join a 7.7mm splined shaft (B) - as strongly as possible.

    Thus far I have tried:

    Threading shaft (A) to 5mm (fine 0.5mm),...
  14. Replies
    4
    Views
    4,153

    Try changing the design so the surface the lamps...

    Try changing the design so the surface the lamps sit on is curved. That will give you better spread ad negate the narrow beam of output of most std LEDs. Google is your friend as there are now many...
Results 1 to 14 of 14