Search:

Type: Posts; User: Cragyon

Page 1 of 12 1 2 3 4

Search: Search took 0.00 seconds.

  1. Not to derail this thread but what does the...

    Not to derail this thread but what does the manufacturer have to say or recommend for mounting?

    Are there install examples for similar or exact applications?
  2. First, to do the statics calculations one will...

    First, to do the statics calculations one will need a free body diagram. This should be provided by you...
  3. Thread: Nano chips

    by Cragyon
    Replies
    1
    Views
    415

    - Unknown, but I doubt it. - Yes, with the...

    - Unknown, but I doubt it.

    - Yes, with the right resolution.

    - I doubt it without a lot of effort.

    There are doggy and cat chips that can be implanted which are read with special hand held...
  4. Replies
    1
    Views
    418

    Some Math Mnemonic's

    These will help you to remember some general math operations.

    Trigonometry

    Sohcahtoa

    Soh...
    Sine = Opposite / Hypotenuse
    ...cah...
    Cosine = Adjacent / Hypotenuse
  5. Replies
    1
    Views
    629

    It's "Hydraulic Press".. See: ...

    It's "Hydraulic Press"..

    See:

    https://www.engineersedge.com/hydraulic/linear-actuators.htm

    https://www.engineersedge.com/calculators/fluids/cylinder-extend-calculator.htm
  6. Replies
    3
    Views
    736

    Can you provide a free body loading diagram?

    Can you provide a free body loading diagram?
  7. Nothing worse than a poster that tries to change...

    Nothing worse than a poster that tries to change the question and claim the responder is "live in a theoretical perfect world".

    "is that the CMM program only constructs a circle from the bore -...
  8. Replies
    1
    Views
    990

    See the following graphic. 2576

    See the following graphic.

    2576
  9. Show your calculations -

    Show your calculations -
  10. You could actually use the "Heat Loss Double-Pane...

    You could actually use the "Heat Loss Double-Pane Window Equation and Calculator".

    https://www.engineersedge.com/heat_transfer/heat_loss_doublepane_window_13864.htm

    Just set the k to the values...
  11. You want a Hydraulic Flow Control Valve,...

    You want a Hydraulic Flow Control Valve, specifically a Volumetric flow rate control valve. The pressure will drop linear with constant flow out of the pressurized system.

    Search the internet for...
  12. Replies
    14
    Views
    1,070

    Zinc or stainless should be fine unless you're...

    Zinc or stainless should be fine unless you're operating in a high salt environment.

    Usually, there is a thread coating on the fitting threads to help minimize corrosion also it's common to see a...
  13. Replies
    5
    Views
    854

    I think too that bolt and nuts are usually thread...

    I think too that bolt and nuts are usually thread cut before case hardening so when cutting more threads tends to less accurate.

    You may need to die or tap the threads several times.
  14. Replies
    7
    Views
    1,423

    Typical NEMA 34 frame stepper motors are rated at...

    Typical NEMA 34 frame stepper motors are rated at more than 30 lb-in and some as high as 1300 lb-in and all weight about the same. Not seeing your challenge in locating one.


    If weight is the...
  15. Replies
    3
    Views
    938

    There's a "Forced Air Flow Convection Cooling....

    There's a "Forced Air Flow Convection Cooling. Fan Air Flow Required for Heat Sinking Formulas and Calculator" on Engineers Edge.

    See: Fan Air Flow Required for Heat Sinking Formulas and Calculator
  16. Replies
    4
    Views
    860

    If the bearing is sized properly, to the loads,...

    If the bearing is sized properly, to the loads, thermal environment, RPM, etc. ... no, the bearing will not "wear out quickly".
  17. Replies
    1
    Views
    918

    Could be a type of grease gun pump.

    Could be a type of grease gun pump.
  18. Replies
    0
    Views
    1,066

    Merry Christmas Everyone!

    Merry Christmas Everyone!

    2536
  19. Replies
    4
    Views
    1,160

    "Home is built to code." Assuming you can...

    "Home is built to code."


    Assuming you can see the wood structure I would put eyes on the actual deflection in action.. Get some well fed friends or what ever and have them walk the floor and...
  20. Agree and agree. "The Short Run and Long Run"...

    Agree and agree.

    "The Short Run and Long Run" overview discusses lost jobs but fails to address the individual challenges that comes with that.


    There are so many of us that are not willing to...
  21. Using Engineers Edge 2D Statics Modeler I get.. ...

    Using Engineers Edge 2D Statics Modeler I get..

    2529

    https://www.engineersedge.com/calculators/statics-modeler/statics-2d-modeling.htm#
  22. Replies
    1
    Views
    1,197

    Very creative! Use what you have design and...

    Very creative! Use what you have design and engineering at its best.
  23. Replies
    2
    Views
    1,566

    Every stress-strain plot I've seen was reported...

    Every stress-strain plot I've seen was reported in actual units. I don't think the strain is being report as a % but being converted into a multiple for ease of reading the plot.

    A note would...
  24. Probably using Profile of a Surface/line. See:...

    Probably using Profile of a Surface/line.

    See: https://www.engineersedge.com/catalog/product_info.php/products_id/656/
  25. Replies
    1
    Views
    1,589

    It's best to ask the asker which is "Underwriters...

    It's best to ask the asker which is "Underwriters Laboratory".

    Probably means size variations or number of wires/strands etc... Again, see sentence above.
Results 1 to 25 of 279
Page 1 of 12 1 2 3 4