# Search:

Page 1 of 4 1

1. ## Thread: Help Request: Calculate Tank Level Based on Pressure

Replies
1
Views
107

### You need to determine the Hydrostatic Pressure vs...

You need to determine the Hydrostatic Pressure vs Depth.

The formula is P = H d

Where:

P = pressure
H = height or depth
d = density of fluid
2. ## Thread: Engineers Edge Forum Question

Replies
4
Views
578

So, I searched your registration email on Google and found you're a well known spammer. - I doubt you'll be back but I did ban your access and changed your thread title from "Vibration" to a more...

Replies
2
Views
962

### Webpage has been updated to show thread graphics...

Webpage has been updated to show thread graphics sufficient for an equation.

Replies
1
Views
868

### Most calculators are unit less unless otherwise...

Most calculators are unit less unless otherwise indicated.

For example:
https://www.engineersedge.com/beam_bending/calculators_protected/beam_deflection_3.htm

The units are suggested for the...
5. ## Thread: Square Tubing For Portable Livestock Systems, Common Grades & Sizes

Replies
8
Views
839

### FYI: No promotion or posting of "sourcing",...

FYI: No promotion or posting of "sourcing", companies, etc. allowed here.
6. ## Thread: I need to find a Motor for a project

Replies
7
Views
1,423

### NOTE: Vendors are not allowed to post...

NOTE:

Vendors are not allowed to post recommendations here.

Use the internet and contact potential suppliers directly.
7. ## Thread: Code standard for hole callout note formats

Replies
3
Views
1,810

### ASME Y14.5-2009 and 2018. Technically 3X is...

ASME Y14.5-2009 and 2018.

Technically 3X is more correct than 3 PL.
8. ## Thread: Free-body diagram for beam element. (partial derivatives)

Replies
1
Views
1,546

### Looks like homework, at the least exclusively...

Looks like homework, at the least exclusively academic.
9. ## Thread: stuck on this question concerning pumping water, any help would be appreciated

Replies
1
Views
551

### Is this homework?

Is this homework?
10. ## Thread: How to create undercut channel in eyeglass frame to hold plastic tube

Replies
5
Views
1,543

### You cannot attach images from your gmail (email)...

You cannot attach images from your gmail (email) account..

insert/upload images in your post. Look for the "Insert Image" icon when posting.

Replies
4
Views
1,382

### Vendor searches and posting not allowed on...

Vendor searches and posting not allowed on Engineers Edge. Otherwise it would be a spam-a-thon here.

It's in the rules.. Closing thread.
12. ## Thread: Nail salon ventilation

Replies
1
Views
918

### Consult an local HVAC service provider. Thread...

Consult an local HVAC service provider.

13. ## Thread: Motor with brake and gearbox for high torque application

Replies
1
Views
1,201

### Thread locked down - no posting. Requests like...

Thread locked down - no posting. Requests like this ALWAYS lead to a spam-a-thon, not here. [/COLOR]
14. ## Thread: Angle Iron Stress

Replies
9
Views
80,472

### The original thread has not been active since...

The original thread has not been active since 2012... Not sure you will an answer given that there are so many unknowns is your design, application and the age of this thread..
15. ## Thread: Reference for Table

Replies
1
Views
1,127

### Data comes from a variety of sources. NIST:...

Data comes from a variety of sources. NIST: National Institute of Standards and Technology is the primary source.
16. ## Thread: Who Is The Manufactuerer of this Heavy Hex Nut

Replies
2
Views
1,742

### You sure it is a logo? Contact the equipment...

You sure it is a logo? Contact the equipment manufacturer which the nut came off of..
17. ## Thread: backup power for old sailboat

Replies
8
Views
5,364

### An electric motor needs power - which would be...

An electric motor needs power - which would be batteries. You would need a lot of weight and money invested in batteries have a limited range where you could just installing a small out gas outboard...
18. ## Thread: Cutting 1060 plate

Replies
6
Views
1,885

### Yes, there will be change in the grain structure...

Yes, there will be change in the grain structure and mechanical characteristics of the carbon steel within the Heat Affected Zone (HAZ). May or may not matter.
19. ## Thread: Cutting 1060 plate

Replies
6
Views
1,885

### Cut with what process?

Cut with what process?
20. ## Thread: Multi-stage scissors lift

Replies
1
Views
1,501

### Just the mass on the lower levels..

Just the mass on the lower levels..

Replies
1
Views
2,204

### Homework not allowed by forum rules.. ...

Homework not allowed by forum rules..

22. ## Thread: Bean Deflection Macaulay’s Method

Replies
1
Views
3,323

### Another homework assignment. What are...

Another homework assignment.

What are Engineers Edge rules regarding school homework?

23. ## Thread: Stress concentration factor and notch sensitivity in a shaft

Replies
1
Views
1,313

Replies
0
Views
11,762

### Disposable/Temporary Email Addresses Not Allowed

Due to an ongoing problem with spammers of various methods using disposable or temporary emails we will not be allowing posts from user registering with these. Existing user with disposable emails...