# Search:

Type: Posts; User: Cragyon

Page 1 of 12 1

## Search: Search took 0.00 seconds; generated 59 minute(s) ago.

by Cragyon
Replies
1
Views
129

### - Unknown, but I doubt it. - Yes, with the...

- Unknown, but I doubt it.

- Yes, with the right resolution.

- I doubt it without a lot of effort.

There are doggy and cat chips that can be implanted which are read with special hand held...
2. ## Thread: Some Math Mnemonic's

by Cragyon
Replies
1
Views
213

### Some Math Mnemonic's

Trigonometry

Sohcahtoa

Soh...
Sine = Opposite / Hypotenuse
...cah...
3. ## Thread: Double hydraulic press

by Cragyon
Replies
1
Views
408

### It's "Hydraulic Press".. See: ...

It's "Hydraulic Press"..

See:

https://www.engineersedge.com/hydraulic/linear-actuators.htm

https://www.engineersedge.com/calculators/fluids/cylinder-extend-calculator.htm

by Cragyon
Replies
3
Views
499

5. ## Thread: Measuring complex Position features / position to 3 datums

by Cragyon
Replies
4
Views
711

### Nothing worse than a poster that tries to change...

Nothing worse than a poster that tries to change the question and claim the responder is "live in a theoretical perfect world".

"is that the CMM program only constructs a circle from the bore -...
6. ## Thread: Describing Different Types of Structures

by Cragyon
Replies
1
Views
775

### See the following graphic. 2576

See the following graphic.

2576

by Cragyon
Replies
3
Views
1,049

8. ## Thread: Combined Thermal Conductivity of I Beam with different k values

by Cragyon
Replies
4
Views
815

### You could actually use the "Heat Loss Double-Pane...

You could actually use the "Heat Loss Double-Pane Window Equation and Calculator".

https://www.engineersedge.com/heat_transfer/heat_loss_doublepane_window_13864.htm

Just set the k to the values...
9. ## Thread: Hydraulic circuit - Linear pressure drop from a pressurized system.

by Cragyon
Replies
1
Views
587

### You want a Hydraulic Flow Control Valve,...

You want a Hydraulic Flow Control Valve, specifically a Volumetric flow rate control valve. The pressure will drop linear with constant flow out of the pressurized system.

Search the internet for...
10. ## Thread: Titanium or Stainless steel?

by Cragyon
Replies
11
Views
623

### Zinc or stainless should be fine unless you're...

Zinc or stainless should be fine unless you're operating in a high salt environment.

Usually, there is a thread coating on the fitting threads to help minimize corrosion also it's common to see a...

by Cragyon
Replies
5
Views
621

### I think too that bolt and nuts are usually thread...

I think too that bolt and nuts are usually thread cut before case hardening so when cutting more threads tends to less accurate.

You may need to die or tap the threads several times.
12. ## Thread: I need to find a Motor for a project

by Cragyon
Replies
7
Views
1,139

### Typical NEMA 34 frame stepper motors are rated at...

Typical NEMA 34 frame stepper motors are rated at more than 30 lb-in and some as high as 1300 lb-in and all weight about the same. Not seeing your challenge in locating one.

If weight is the...
13. ## Thread: Looking for air flow number

by Cragyon
Replies
3
Views
732

### There's a "Forced Air Flow Convection Cooling....

There's a "Forced Air Flow Convection Cooling. Fan Air Flow Required for Heat Sinking Formulas and Calculator" on Engineers Edge.

See: Fan Air Flow Required for Heat Sinking Formulas and Calculator
14. ## Thread: Bidirectional bearing wear

by Cragyon
Replies
4
Views
674

### If the bearing is sized properly, to the loads,...

If the bearing is sized properly, to the loads, thermal environment, RPM, etc. ... no, the bearing will not "wear out quickly".

by Cragyon
Replies
1
Views
700

### Could be a type of grease gun pump.

Could be a type of grease gun pump.
16. ## Thread: Merry Christmas Everyone!

by Cragyon
Replies
0
Views
748

### Merry Christmas Everyone!

Merry Christmas Everyone!

2536
17. ## Thread: Solution To Home Floor Joist Deflection?

by Cragyon
Replies
4
Views
824

### "Home is built to code." Assuming you can...

"Home is built to code."

Assuming you can see the wood structure I would put eyes on the actual deflection in action.. Get some well fed friends or what ever and have them walk the floor and...
18. ## Thread: Don't Fear Change by the Introduction of New Technology

by Cragyon
Replies
3
Views
871

### Agree and agree. "The Short Run and Long Run"...

Agree and agree.

"The Short Run and Long Run" overview discusses lost jobs but fails to address the individual challenges that comes with that.

There are so many of us that are not willing to...
19. ## Thread: Reaction Forces - Bending Moment Diagram - Shear Force Diagram

by Cragyon
Replies
1
Views
768

### Using Engineers Edge 2D Statics Modeler I get.. ...

Using Engineers Edge 2D Statics Modeler I get..

2529

https://www.engineersedge.com/calculators/statics-modeler/statics-2d-modeling.htm#

by Cragyon
Replies
1
Views
973

### Very creative! Use what you have design and...

Very creative! Use what you have design and engineering at its best.
21. ## Thread: Calculating Youngs Modulus

by Cragyon
Replies
2
Views
1,275

### Every stress-strain plot I've seen was reported...

Every stress-strain plot I've seen was reported in actual units. I don't think the strain is being report as a % but being converted into a multiple for ease of reading the plot.

A note would...
22. ## Thread: Specifying tolerances for multiple features in press fit

by Cragyon
Replies
4
Views
1,316

### Probably using Profile of a Surface/line. See:...

Probably using Profile of a Surface/line.

See: https://www.engineersedge.com/catalog/product_info.php/products_id/656/

by Cragyon
Replies
1
Views
1,275

Probably means size variations or number of wires/strands etc... Again, see sentence above.
24. ## Thread: Interpreting a Stress - Strain Curve

by Cragyon
Replies
1
Views
1,229

Also, the stress strain curve is incomplete.
25. ## Thread: Coil Rod/Bolt/Nut Specifications

by Cragyon
Replies
10
Views
3,423

### Looks like a ball screw thread. See bottom of...

Looks like a ball screw thread.

See bottom of this webpage: https://www.engineersedge.com/mechanics_machines/ball_screw_design_equations_15235.htm
Results 1 to 25 of 277
Page 1 of 12 1