Search:

Type: Posts; User: Kelly Bramble

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. That's probably a UV Spraying Coating.

    That's probably a UV Spraying Coating.
  2. Replies
    1
    Views
    223

    A image would be helpful..

    A image would be helpful..
  3. Replies
    0
    Views
    226

    Animation How A Gearbox Works

    This animation shows how an automotive manual gearbox works.

    2587
  4. Storage system for storing rainwater and using it when needed

    Tank configuration with overflow.

    2586
  5. I would try an organization that specializes in...

    I would try an organization that specializes in engineering and design professionals for hire.

    Engineers Edge gets lots of internet traffic however I'm pretty sure you're not going to find much...
  6. All GD&T Tolerance boundaries are applied to the...

    All GD&T Tolerance boundaries are applied to the full depth, width and length of the feature.

    X and Y measurements you're referring to are simple 2-d measurements from a specified and established...
  7. No... I think this is the second question in a...

    No...

    I think this is the second question in a week regarding the interpretation and setup for measurement to datums. Position tolerance can be 2D in very thin cross sections like a .0005" shim...
  8. Replies
    1
    Views
    612

    If it's a surface - it can be a datum. This works...

    If it's a surface - it can be a datum. This works as defined. Datum C can be simulated with two collapsing surfaces that are parallel to the engineering drawing graphics as specified. A CMM would...
  9. Replies
    17
    Views
    951

    I doubt it's an off-the-shelf gear. Probably...

    I doubt it's an off-the-shelf gear.

    Probably need to find somebody that can reproduce it from what you have
  10. Parallelism is measured from the specified datum...

    Parallelism is measured from the specified datum which is simulated at the tangent plane of that datum feature. One might place that datum surface against a surface plate thus contacting the three...
  11. See: ...

    See:

    https://www.engineersedge.com/heat_transfer/conduction_multilayer_isothermal_wall.htm
  12. Replies
    1
    Views
    642

    Academic.... this is homework created by...

    Academic.... this is homework created by somebody that wanted to pose a math challenge to students.
  13. Replies
    1
    Views
    623

    Profile of surface tolerance by default is...

    Profile of surface tolerance by default is bi-lateral equal (half to the inside and half to the outside of the profile).

    Therefore, a perfect world go gage size is an oblong shape (15 - 0.1) x (8...
  14. You can't.. Stress and deflection is...

    You can't..

    Stress and deflection is typically not linear not is it simple and understood anecdotally.

    Without a free body diagram, materials and engineering detail calculations - you don't...
  15. Replies
    0
    Views
    365

    Right tool for the job

    Using the right appliance for the job:

    2563
  16. Yes, but note that LMB is as related and assigned...

    Yes, but note that LMB is as related and assigned to a Datum Feature.




    No... too general except for selected cases.
  17. BS8888 does not provide specific guidance on...

    BS8888 does not provide specific guidance on concentricity tolerance however paragraph 9.1 - 9.3, general tolerances does suggest the usage of BS EN 22768-1 also known as ISO 2768-1 for general...
  18. Replies
    1
    Views
    296

    LMB y MMB son modificadores de datum y pueden...

    LMB y MMB son modificadores de datum y pueden estar relacionados con tolerancias de posición.
  19. Replies
    11
    Views
    497

    I have a boat - it gets launched in salt water....

    I have a boat - it gets launched in salt water. The calipers are aluminum and the bleeder valves are steel and coated. Brakes should only be bled once maybe twice in the useful life. I always water...
  20. I’m sure you’re aware that you can mix carbon and...

    I’m sure you’re aware that you can mix carbon and nickel steels for functional requirements. For example, more than thirty years ago I worked at Bell Helicopter Textron and designed fatigue testing...
  21. You seem to be changing the question to fit? ...

    You seem to be changing the question to fit? Your questions now appear to be more academic in nature with a need for sourcing. Depending on volume buy as local as you can and as common materials as...
  22. Nobody can tell you what end material you need to...

    Nobody can tell you what end material you need to satisfy stress requirements or some generic weight vs cost vs strength requirements you may need based on a forum post.

    You need a design layout...
  23. A513 = ASTM A513, which is simply a specification...

    A513 = ASTM A513, which is simply a specification of carbon steel commonly available as 1010, 1020, etc..

    Carbon steel is very weldable, easily formed with the right tools. All you rally need to...
  24. Replies
    1
    Views
    323

    I would use a simple lever calculation to...

    I would use a simple lever calculation to determine the force applied by the moment force then add that load to the loading on the bolt from torque.

    See:...
  25. Replies
    0
    Views
    313

    New Technology and Protestors.

    Protesting new technology.

    2549
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4