Search:

Type: Posts; User: Hudson

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    291

    You need help with the equations? Moment...

    You need help with the equations?

    Moment from arm = 100 kg x 650 mm = 65000 kg mm

    (22.5 mm x Force on bottom bolts) + (152.5 mm x Force on top bolts) = 65000 kg mm in the opposite...
  2. Replies
    7
    Views
    291

    A ball park method: You have a moment on the...

    A ball park method:

    You have a moment on the beam that is transferred to the plate. Presumably you know the distance from the bolt holes to the bottom edge of the plate.

    I would calculate...
  3. Replies
    6
    Views
    253

    You have not presented a clear picture of the...

    You have not presented a clear picture of the problem or exactly how your equation came to be. We went from casting a cylinder to a rectangular tube of unknown dimensions and we added a speed but...
  4. Replies
    6
    Views
    253

    To convert rpm to radians per second, multiply by...

    To convert rpm to radians per second, multiply by .10472
    The obtain centrifugal force you need to square the rotating speed so to convert to rpm^2 use .10472^2 or .010966
    You also need to convert...
  5. Water molecules are very polarized and are pulled...

    Water molecules are very polarized and are pulled apart by the opposite charges in the equipment you illustrate. It is a DC current not a frequency phenomenon.

    You can store energy in this...
  6. Replies
    1
    Views
    256

    Are you referring to the bending owing to...

    Are you referring to the bending owing to gravitational force? If so, is the shaft uniform in dimensions so that you can treat it like a uniformly loaded beam? Then you probably want the shaft...
  7. Replies
    1
    Views
    206

    One method is to use a press fit and/or a...

    One method is to use a press fit and/or a retaining ring on the shaft in the fixed location and have a slip or sliding fit on the floating end. In both cases the outer race is fixed.
  8. Replies
    4
    Views
    488

    My review suggests the original post was...

    My review suggests the original post was manufactured by rolling - in self-pity. The material is probably snowflake.



    It is entirely possible that the interviewer was trying to be helpful...
  9. Replies
    2
    Views
    234

    Check out sonic welding. There is also some...

    Check out sonic welding.

    There is also some pretty good glue in the plumbing aisle.
  10. Replies
    6
    Views
    278

    force on pins

    The projecting pins will be pushed outward or inward by the mating holes.

    This force exerts a bending moment on the pins attempting to rotate them.

    The force also tries to move the pins away...
  11. Thread: No. of Holes

    by Hudson
    Replies
    5
    Views
    482

    Multiply the pressure times the area inside the...

    Multiply the pressure times the area inside the gasket to get the force trying to push the cover off the valve. The total clamp load of the bolts should be several times this value. How many times...
  12. Replies
    3
    Views
    277

    You'd think it would work just fine as the...

    You'd think it would work just fine as the external pressure is only 1/10 of the rated internal pressure capacity.
  13. Replies
    3
    Views
    220

    Another option is a stepper motor. You have 12...

    Another option is a stepper motor. You have 12 Volts. You'll need, in addition to the motor, a driver that regulates D.C.direction and power to the motor coils to determine position and motion plus...
  14. Replies
    3
    Views
    289

    An observation: The holes on the smallest bolt...

    An observation: The holes on the smallest bolt circle are near the weakest part and none of the holes are aligned for manufacturing.
  15. Replies
    6
    Views
    278

    The deliberate misalignment of locating pins...

    The deliberate misalignment of locating pins creates an "interference fit".
  16. Replies
    5
    Views
    724

    Can you machine a 10mm hex on the end of the 12mm...

    Can you machine a 10mm hex on the end of the 12mm shaft and let maintenance use a socket wrench and extension?
  17. Replies
    4
    Views
    1,013

    A file or tiny grinder on a bottom edge would...

    A file or tiny grinder on a bottom edge would remove any plating and reveal the base material.
  18. You can inject steam heated water into the...

    You can inject steam heated water into the discharge side of the pump or perhaps use the steam alone to pump the water.

    steam engine boilers, especially on locomotives which did not recirculate...
  19. Replies
    4
    Views
    813

    Why not tolerance a wall thickness to the O.D....

    Why not tolerance a wall thickness to the O.D. that can be checked with a simple ball or tube micrometer instead of relying on CMM and inspection tables. Think like a machinist.
  20. Replies
    10
    Views
    993

    Do I see 'B' and 'C' datums as the edge of both a...

    Do I see 'B' and 'C' datums as the edge of both a 3" and an 8" square part? Then you call out parts to be centered?

    Why not make two bolt holes a common datum in the x & Y plane?
  21. Replies
    2
    Views
    969

    Sounds dangerous but, first determine if the...

    Sounds dangerous but, first determine if the floor can handle the load. If you have two 1 foot wide, seven foot long supports at the base and 21,000 lbs supported by them that's 1500 lbs/sq.ft if...
  22. Replies
    2
    Views
    642

    Consider a urethane adhesive for windshields. ...

    Consider a urethane adhesive for windshields.

    https://www.3m.com/3M/en_US/company-us/all-3m-products/~/3M-Auto-Glass-Urethane-Windshield-Adhesive/?N=5002385+3293242009&rt=rud
  23. Replies
    2
    Views
    1,015

    Are they multi-million dollar dies? Years ago,...

    Are they multi-million dollar dies? Years ago, when the earth was thought to be cooling, auto makers used a free machining, low melting alloy called Kirksite for fender dies.

    More recently,...
  24. You have a .002 cylindricity and a roundness call...

    You have a .002 cylindricity and a roundness call out. That seems like double dimensioning to me.

    Could you just call out a .005 cylindricity and a surface finish on the basic shaft diameter and...
  25. Look harder for 1" couplings. They should be...

    Look harder for 1" couplings. They should be less than a dollar for the PVC type.
Results 1 to 25 of 169
Page 1 of 7 1 2 3 4