Search:

Type: Posts; User: Kelly Bramble

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 58 minute(s) ago.

  1. The final functional test should reflect the way...

    The final functional test should reflect the way the strut is functionally used.
  2. Replies
    3
    Views
    261

    See: AGMA Worm and Spur Gwar Design Equations...

    See:

    AGMA Worm and Spur Gwar Design Equations and Calculator

    https://www.engineersedge.com/calculators/agma_worm_and_spur_gear_design_equations_and_calculators_15310.htm
  3. Look at the time that the torque is applied and...

    Look at the time that the torque is applied and any cyclic loading. Energy will be absorbed by the flexible shaft but eventually total input torque will be translated through the shaft.
  4. Replies
    1
    Views
    380

    Current, voltage and crosstalk requirements would...

    Current, voltage and crosstalk requirements would be you only concern. Possible solution.
  5. If this is a closed system pressured above that...

    If this is a closed system pressured above that produced by gravity then the pressure is the same everywhere except during flow.

    If it is a gravity system the system will vary with elevation.
    ...
  6. Replies
    4
    Views
    444

    Hydraulic accumulators are sized and pressured to...

    Hydraulic accumulators are sized and pressured to the system operational volumetric and pressure requirements. If you install an accumulator that operates at the wrong pressure charge and/or...
  7. Replies
    4
    Views
    444

    The Toyota part number is 4795030010 which also...

    The Toyota part number is 4795030010 which also fits the 4Runner and RAV4.

    Why would you not just go to a Toyota dealership and buy the OEM part?

    Toyota Parts Center Online sells them...
  8. Replies
    9
    Views
    541

    It has a tolerance when not produced at MMC size....

    It has a tolerance when not produced at MMC size. Ultimately, the value of this specification is that the are more size and as-manufactured position tolerances available for manufacturing.

    It's...
  9. Replies
    9
    Views
    541

    I agree in ~ general with your statement; however...

    I agree in ~ general with your statement; however engineering, manufacturing, quality and others whom must create or interpret an engineering drawing should have sufficient training and or experience...
  10. Where an arrow or a clear drafting association...

    Where an arrow or a clear drafting association with surface is given - that's the surface roughness required.

    For those surface roughness specifications within the brackets - contact the...
  11. Replies
    9
    Views
    541

    The MCC modifier means that at that specified...

    The MCC modifier means that at that specified size (Maximum Material Condition) which the smallest as-built allowed by tolerance for a hole feature or the largest allowed as-built by tolerance and...
  12. Replies
    9
    Views
    541

    If you had posted an image or exact details of...

    If you had posted an image or exact details of the position tolerance specification we could chart it out for you..

    Does the specification include a MMC modifier (Circle M) after the zero...
  13. The math is somewhat tedious, I recommend you use...

    The math is somewhat tedious, I recommend you use the 2D statics modeler on this website.

    https://www.engineersedge.com/calculators/statics-modeler/statics-2d-modeling.htm
  14. 3D Printer Troubleshooting and Repair

    I have 3D printer that recently had a control circuit board failure. After some trouble shooting I verified the Rambo 1.3L Z-Axis circuit was not functioning properly. Rambo boards are commonly used...
  15. Replies
    8
    Views
    355

    FYI, My 25' center console w/ 2 Yamaha 200hp I4's...

    FYI, My 25' center console w/ 2 Yamaha 200hp I4's has hydraulic steering - no pump required, works good... Hydraulic assist would make the steering one finger response though.. My brother in-law...
  16. Replies
    8
    Views
    355

    Ok, so I'll agree to your terminology and call it...

    Ok, so I'll agree to your terminology and call it a "stick steering system". I too am a boat guy, my entire life so what we are talking about for the other readers is instead of a helm wheel - you...
  17. Replies
    7
    Views
    1,799

    ASME Y14.5M-1994 does not provide specific...

    ASME Y14.5M-1994 does not provide specific default tolerances. Nor does any other dimensioning and tolerancing standard (ANSI, ISO, DIN, etc.).

    The engineering drawing is incomplete without...
  18. Replies
    8
    Views
    355

    What you're looking for is also called a Tiller...

    What you're looking for is also called a Tiller Steering system, there's more than one company offering a solution and I doubt you can even come close to building and installing a system cheaper than...
  19. Replies
    9
    Views
    347

    You need a concept first, not sure why you have a...

    You need a concept first, not sure why you have a cross section from which to work with.
  20. Replies
    9
    Views
    347

    Are you serious? What other information do you...

    Are you serious?

    What other information do you have, specifications, parts list, 3D model..
  21. Ratchet actuated gears... Ratchets work in the...

    Ratchet actuated gears... Ratchets work in the direction of intended operation.

    See:

    https://www.engineersedge.com/calculators/ratchet_type_gear_design_15333.htm
  22. Replies
    1
    Views
    393

    Tried it, have a structure sensor scanner (google...

    Tried it, have a structure sensor scanner (google it) did not really work. The cost for a quality 3D scanner + printer that can do ABS, PETG etc. not worth it. Can't imagine your plastic parts break...
  23. Flow rate will be derived from differential...

    Flow rate will be derived from differential pressure, size of pipes, etc..

    And, yes there is a way to calculate flow in defined fluid systems - - but you have not provided any usable information...
  24. Replies
    3
    Views
    291

    See the following webpage: Select the loading...

    See the following webpage: Select the loading configuration from the images:

    https://www.engineersedge.com/beam_calc_menu.shtml

    If you cannot find the loading configuration see the following...
  25. Gd&t

    Datum features are specified with identifying letters and every letter can be used except I, O and Q. Depending on the functional or manufacturing requirements of a part or feature the identified...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4