Search:

Type: Posts; User: Kelly Bramble

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Regardless of the fixture structural members...

    Regardless of the fixture structural members materials (Aluminum, fiberglass, or whatever..) the features/parts on the fixturing tools that contact the features on the part or assembly should be...
  2. Replies
    1
    Views
    151

    Typically, 52110 chrome steel is used in bearing...

    Typically, 52110 chrome steel is used in bearing and bearing components.


    I'm sure you can thread the material though I doubt it is easy and I doubt you would have too much problems it if...
  3. "Can stainless be shaped like a car fender? " ...

    "Can stainless be shaped like a car fender? " Yes.
  4. Replies
    1
    Views
    247

    Try one of these: Ingenious Mechanisms I...

    Try one of these:


    Ingenious Mechanisms I
    IIngenious Mechanisms II
    Ingenious Mechanisms III
    Ingenious Mechanisms IV
  5. Replies
    1
    Views
    518

    See this: Heat Loss along an Insulated Pipe...

    See this: Heat Loss along an Insulated Pipe Equation and Calculator.
  6. Replies
    4
    Views
    771

    Note that according to ASME Y14.5-2009 and...

    Note that according to ASME Y14.5-2009 and previous dimensioning and tolerancing standards reference dimensions are not binding to quality.

    Moreover, reference dimensions are dimensions contained...
  7. Replies
    4
    Views
    771

    The 15 mm tolerance will be the default defined...

    The 15 mm tolerance will be the default defined on the engineering drawing. If there is not a default tolerance you will need one.
  8. See: Hole MMC Tolerance Calculator ...

    See:

    Hole MMC Tolerance Calculator

    https://www.engineersedge.com/calculators/mmc-size-geometric-tolerance.htm
  9. Replies
    5
    Views
    791

    By default, position location measurements should...

    By default, position location measurements should be made to the pitch diameter. Though you may get adequate measurement from the major diameter as well. To very the pitch diameter size and...
  10. For clarity on dimensioning a slot I was...

    For clarity on dimensioning a slot I was recommending that the op place the dimensions NORMAL to the slot feature not change the physical orientation of the slot feature. Though I do think the...
  11. They are just an led diode...

    They are just an led diode...
  12. Stepper motor mechanism and an electronics...

    Stepper motor mechanism and an electronics engineer.
  13. flexible neon blue light... Search for it

    flexible neon blue light... Search for it
  14. So, concrete is great in compression and poor in...

    So, concrete is great in compression and poor in tension. Which is why concrete includes steel rebar located towards the tension side in pavement.

    The op could fill the tubes with wood or another...
  15. You have an iron board... Sure, fill it with...

    You have an iron board... Sure, fill it with concrete though weight will increase. Be sure you have plenty footing that is wide.

    2297
  16. As an ASME certified Senior level GDTP...

    As an ASME certified Senior level GDTP professional since 1997 (Google me), and having wrote and published eight books on dimensioning and tolerancing - NO... A parallel dimension does not change...
  17. ? Placing the 8mm dimension parallel...

    ? Placing the 8mm dimension parallel (perpendicular to radius) with the length does not change the intent nor the specification - it is most correct per. ASME and ISO.

    See ASME Y14.5-2009,...
  18. Yes, the 8mm feature is drawn and dimensioned...

    Yes, the 8mm feature is drawn and dimensioned symmetrical about Datum B. Your 8 mm dimension should actually be placed parallel to the 8MM feature, or perpendicular to the end radius.
  19. Replies
    5
    Views
    1,731

    For b, see Hydrostatic Pressure vs Depth ->...

    For b, see Hydrostatic Pressure vs Depth -> https://www.engineersedge.com/fluid_flow/hydrostatic-pressure.htm

    Also,

    https://www.engineersedge.com/fluid_flow/relationship_depth_pressure.htm
    ...
  20. Replies
    5
    Views
    1,731

    The pressure along length h needs to be greater...

    The pressure along length h needs to be greater than the pressure along length b unless there is an external force (torque) applied to the mechanism.
  21. Replies
    3
    Views
    954

    What makes you think it "stick to skin strongly"?

    What makes you think it "stick to skin strongly"?
  22. See: Stress Strain curve ...

    See:

    Stress Strain curve
  23. Regardless of which dimensioning and tolerancing...

    Regardless of which dimensioning and tolerancing standard you are referring to (ASME or ISO) the surface variations allowed by the surface finish specification will always be contained within the...
  24. Replies
    1
    Views
    563

    Yes, the datum specification is legitimate. I...

    Yes, the datum specification is legitimate. I don't think ISO-1101 not ASME-Y14.5 will have an example with an explanation that is identical.
  25. 1) 3D print with plastic 2) Injection mold in...

    1) 3D print with plastic
    2) Injection mold in sections
    3) Form soft plastic or metal over mandrel
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4