Search:

Type: Posts; User: Cragyon

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    146

    It's "Hydraulic Press".. See: ...

    It's "Hydraulic Press"..

    See:

    https://www.engineersedge.com/hydraulic/linear-actuators.htm

    https://www.engineersedge.com/calculators/fluids/cylinder-extend-calculator.htm
  2. Replies
    2
    Views
    267

    Can you provide a free body loading diagram?

    Can you provide a free body loading diagram?
  3. Nothing worse than a poster that tries to change...

    Nothing worse than a poster that tries to change the question and claim the responder is "live in a theoretical perfect world".

    "is that the CMM program only constructs a circle from the bore -...
  4. Replies
    1
    Views
    625

    See the following graphic. 2576

    See the following graphic.

    2576
  5. Show your calculations -

    Show your calculations -
  6. You could actually use the "Heat Loss Double-Pane...

    You could actually use the "Heat Loss Double-Pane Window Equation and Calculator".

    https://www.engineersedge.com/heat_transfer/heat_loss_doublepane_window_13864.htm

    Just set the k to the values...
  7. You want a Hydraulic Flow Control Valve,...

    You want a Hydraulic Flow Control Valve, specifically a Volumetric flow rate control valve. The pressure will drop linear with constant flow out of the pressurized system.

    Search the internet for...
  8. Replies
    11
    Views
    514

    Zinc or stainless should be fine unless you're...

    Zinc or stainless should be fine unless you're operating in a high salt environment.

    Usually, there is a thread coating on the fitting threads to help minimize corrosion also it's common to see a...
  9. Replies
    5
    Views
    472

    I think too that bolt and nuts are usually thread...

    I think too that bolt and nuts are usually thread cut before case hardening so when cutting more threads tends to less accurate.

    You may need to die or tap the threads several times.
  10. Replies
    7
    Views
    628

    Typical NEMA 34 frame stepper motors are rated at...

    Typical NEMA 34 frame stepper motors are rated at more than 30 lb-in and some as high as 1300 lb-in and all weight about the same. Not seeing your challenge in locating one.


    If weight is the...
  11. Replies
    3
    Views
    595

    There's a "Forced Air Flow Convection Cooling....

    There's a "Forced Air Flow Convection Cooling. Fan Air Flow Required for Heat Sinking Formulas and Calculator" on Engineers Edge.

    See: Fan Air Flow Required for Heat Sinking Formulas and Calculator
  12. Replies
    4
    Views
    611

    If the bearing is sized properly, to the loads,...

    If the bearing is sized properly, to the loads, thermal environment, RPM, etc. ... no, the bearing will not "wear out quickly".
  13. Replies
    1
    Views
    601

    Could be a type of grease gun pump.

    Could be a type of grease gun pump.
  14. Replies
    0
    Views
    631

    Merry Christmas Everyone!

    Merry Christmas Everyone!

    2536
  15. Replies
    4
    Views
    681

    "Home is built to code." Assuming you can...

    "Home is built to code."


    Assuming you can see the wood structure I would put eyes on the actual deflection in action.. Get some well fed friends or what ever and have them walk the floor and...
  16. Agree and agree. "The Short Run and Long Run"...

    Agree and agree.

    "The Short Run and Long Run" overview discusses lost jobs but fails to address the individual challenges that comes with that.


    There are so many of us that are not willing to...
  17. Using Engineers Edge 2D Statics Modeler I get.. ...

    Using Engineers Edge 2D Statics Modeler I get..

    2529

    https://www.engineersedge.com/calculators/statics-modeler/statics-2d-modeling.htm#
  18. Replies
    1
    Views
    835

    Very creative! Use what you have design and...

    Very creative! Use what you have design and engineering at its best.
  19. Replies
    2
    Views
    1,090

    Every stress-strain plot I've seen was reported...

    Every stress-strain plot I've seen was reported in actual units. I don't think the strain is being report as a % but being converted into a multiple for ease of reading the plot.

    A note would...
  20. Probably using Profile of a Surface/line. See:...

    Probably using Profile of a Surface/line.

    See: https://www.engineersedge.com/catalog/product_info.php/products_id/656/
  21. Replies
    1
    Views
    1,136

    It's best to ask the asker which is "Underwriters...

    It's best to ask the asker which is "Underwriters Laboratory".

    Probably means size variations or number of wires/strands etc... Again, see sentence above.
  22. Replies
    1
    Views
    1,074

    Yes, rated stress of wood is dependent on loading...

    Yes, rated stress of wood is dependent on loading direction relative to grain. Loading perpendicular to grain will cause separate.

    Also, the stress strain curve is incomplete.
  23. Replies
    10
    Views
    3,248

    Looks like a ball screw thread. See bottom of...

    Looks like a ball screw thread.

    See bottom of this webpage: https://www.engineersedge.com/mechanics_machines/ball_screw_design_equations_15235.htm
  24. Replies
    2
    Views
    1,216

    Why would you even model it? Are you 3D printing...

    Why would you even model it? Are you 3D printing the gears?

    If machining, determine gear ratio, specify desired industry standard tooth profile, pitch or whatever diameter needed, AGMA tolerance...
  25. Replies
    3
    Views
    661

    Deep drawing or spinning.

    Deep drawing or spinning.
Results 1 to 25 of 275
Page 1 of 11 1 2 3 4