Search:

Type: Posts; User: Kelly Bramble

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. You can ask questions here. I am not sure...

    You can ask questions here.

    I am not sure you'll get an answer as very little SAP is discussed here.
  2. Есть ли у Tekla и SAP справочный форум? Вы...

    Есть ли у Tekla и SAP справочный форум?


    Вы должны там задавать вопросы.
  3. Немногие посетители здесь говорят или пишут...

    Немногие посетители здесь говорят или пишут по-русски. Возможно, вам придется пойти туда, где их больше.


    Я не могу ответить на твой вопрос
  4. Replies
    1
    Views
    152

    A Spectrum analyzer is just a modern...

    A Spectrum analyzer is just a modern Oscilloscope. You would need the relevant sensors that process whatever the radiation is.
  5. Replies
    3
    Views
    231

    I see you're a brand new member, did you have a...

    I see you're a brand new member, did you have a account back in 2009?


    1) Engineers Edge is more than just a discussion forum. Answers folks need are gradually being populated here and all over...
  6. Replies
    2
    Views
    211

    Similar, Ra = Roughness Average RMS =...

    Similar,

    Ra = Roughness Average

    RMS = Root Mean Square

    Math is different but get you similar.
  7. There is almost always a new supplier issue with...

    There is almost always a new supplier issue with existing tough-to-build parts.

    Chances are that existing suppliers have built fixtures or have worked a special process to build your end item. We...
  8. Also, consider that in some installation...

    Also, consider that in some installation applications a flex pipe (bellows or other) can allow for more generous tolerance specifications in the primary piping installation.
  9. Weldments are challenging to hold tight...

    Weldments are challenging to hold tight tolerances without fixtures, post machining etc. Distortions are common due to the extreme temperature variations at the weld affected zone (WAZ) during the...
  10. Replies
    1
    Views
    198

    See: ...

    See:

    https://www.engineersedge.com/beam_bending/beam_bending17.htm
  11. Replies
    3
    Views
    374

    Here's associated formulas and calculator for...

    Here's associated formulas and calculator for flywheel design:

    Flywheel Mass Size Design Equation and Calculator
  12. Replies
    3
    Views
    374

    No.... energy cannot be created from nothing.

    No.... energy cannot be created from nothing.
  13. Your calculations are statically indeterminate...

    Your calculations are statically indeterminate and ignore real world deflections. Moreover, structures are never build in perfect orientation nor are structural members perfect. Thus, some...
  14. Replies
    2
    Views
    1,169

    That's probably a UV Spraying Coating.

    That's probably a UV Spraying Coating.
  15. Replies
    2
    Views
    355

    A image would be helpful..

    A image would be helpful..
  16. Replies
    0
    Views
    341

    Animation How A Gearbox Works

    This animation shows how an automotive manual gearbox works.

    2587
  17. Storage system for storing rainwater and using it when needed

    Tank configuration with overflow.

    2586
  18. I would try an organization that specializes in...

    I would try an organization that specializes in engineering and design professionals for hire.

    Engineers Edge gets lots of internet traffic however I'm pretty sure you're not going to find much...
  19. All GD&T Tolerance boundaries are applied to the...

    All GD&T Tolerance boundaries are applied to the full depth, width and length of the feature.

    X and Y measurements you're referring to are simple 2-d measurements from a specified and established...
  20. No... I think this is the second question in a...

    No...

    I think this is the second question in a week regarding the interpretation and setup for measurement to datums. Position tolerance can be 2D in very thin cross sections like a .0005" shim...
  21. Replies
    1
    Views
    713

    If it's a surface - it can be a datum. This works...

    If it's a surface - it can be a datum. This works as defined. Datum C can be simulated with two collapsing surfaces that are parallel to the engineering drawing graphics as specified. A CMM would...
  22. Replies
    17
    Views
    1,138

    I doubt it's an off-the-shelf gear. Probably...

    I doubt it's an off-the-shelf gear.

    Probably need to find somebody that can reproduce it from what you have
  23. Parallelism is measured from the specified datum...

    Parallelism is measured from the specified datum which is simulated at the tangent plane of that datum feature. One might place that datum surface against a surface plate thus contacting the three...
  24. See: ...

    See:

    https://www.engineersedge.com/heat_transfer/conduction_multilayer_isothermal_wall.htm
  25. Replies
    1
    Views
    806

    Academic.... this is homework created by...

    Academic.... this is homework created by somebody that wanted to pose a math challenge to students.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4