Search:

Type: Posts; User: Kelly Bramble

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Do consider that the imperial (inches) system...

    Do consider that the imperial (inches) system requires matching significant figures for both limit, basic and expressed tolerance without leading zeros. For SI units (metric) there are no training...
  2. Replies
    6
    Views
    57

    Awesome..G:J

    Awesome..G:J
  3. I'm an engineering consultant and trainer in GD&T...

    I'm an engineering consultant and trainer in GD&T as well as DFM/DFMA.

    Usually a miss-match between the target manufacturing process and the limits of tolerance specified. Many organizations have...
  4. Both way are often used in the USA. The...

    Both way are often used in the USA. The tolerances should be based on the intended typical manufacturing process capabilities.

    In the rest of the world, they use ISO 286 part I and II OR ISO 2768...
  5. No... and I've seen a lot of engineering...

    No... and I've seen a lot of engineering drawings.

    Paragraph 3.3.16 Square Symbol ASME specification, the text does says " ... that a single dimension applies to a square shape shall...".

    Let's...
  6. Replies
    6
    Views
    57

    W is typically the total load or force applied, r...

    W is typically the total load or force applied, r might be radius, F is typically force, I agree C is unknown..

    You should consider just redoing the equations and calculations to be sure of what...
  7. Replies
    1
    Views
    79

    The best way to handle that is Engineers Edge...

    The best way to handle that is Engineers Edge "Static's 2D Modeler and Structural Loads Calculator"

    It's here: https://www.engineersedge.com/calculators/statics-modeler/statics-2d-modeling.htm
  8. Replies
    1
    Views
    116

    To get better with dimensioning and tolerancing,...

    To get better with dimensioning and tolerancing, I would suggest that you seek out some training and/or ask an available work mentor to assist.

    This is your first post on Engineers Edge (you've...
  9. All manufacturers of welding equipment offer...

    All manufacturers of welding equipment offer software, systems, computers, etc. to track welding performance, etc..

    Have you searched their websites?
  10. Replies
    3
    Views
    163

    Economics / Cost of Applying GD&T

    More often than not, PROPER application of ASME Y14.5 GD&T decreases the overall cost of part production. Inspection requires the metrology folks to establish an origin, when there are not datums...
  11. Those are great alternative suggestions for...

    Those are great alternative suggestions for storing renewable energy however not all locations have resources available.

    Batteries can and do work very well..
  12. Replies
    0
    Views
    179

    America and her Toilets

    OK, letís have a serious discussion about toilets.

    The current president of the United States claims that sometimes we have to flush 10-15 times before it all goes down. Now, Iím assuming heís...
  13. Christmas Cartesian Coordinate System

    Also called "Datum Reference Frame" or DRF.

    2367
  14. Replies
    1
    Views
    201

    My ~ guess is that at minimum 3 x OD or more full...

    My ~ guess is that at minimum 3 x OD or more full engagement into the pipe each end. The clearance between the internal sleeve and inside pipe diameter would be very important to achieve full...
  15. See "pulse jet engine", also called "RamJet" ....

    See "pulse jet engine", also called "RamJet" . First patented in 1867 by Russian inventor Nikolaj Afanasievich Teleshov.

    You should educate yourself in existing jet and reciprocating engine...
  16. Depends on how the object is supported relative...

    Depends on how the object is supported relative to the applied force.

    Is the object/shape statically located and how?
  17. Replies
    6
    Views
    240

    It's not clear what the loading is from your...

    It's not clear what the loading is from your description but there are six types of stress induced by loading:

    Compression
    Tension
    Shear
    Bending
    Torsion
    Fatigue

    There can also be...
  18. Insufficient information to provide guidance or a...

    Insufficient information to provide guidance or a recommendation..

    What are the mating features?

    Which feature or features provide primary alignment or location?
  19. Replies
    3
    Views
    188

    Search the internet for: Constant speed AC (or...

    Search the internet for:

    Constant speed AC (or DC) Motor
    Variable Speed Electric Motor and Controls
    Adjustable Speed Motor
  20. Replies
    4
    Views
    427

    See and get access too and study up here: ...

    See and get access too and study up here:

    https://www.engineersedge.com/dfm-dfma.htm

    That interviewer was not cut out to be an interviewer. That's right on the mark of unprofessional and most...
  21. There are likely millions of research and testing...

    There are likely millions of research and testing hours into gas turbines. Also unknown number hours of in-field operation and data from which unknown number of scientist and engineers have...
  22. Replies
    2
    Views
    536

    Cost, Out of scope changes, schedule.

    Cost,
    Out of scope changes,
    schedule.
  23. Search the internet for: "expanded metal load...

    Search the internet for:

    "expanded metal load tables"
    or
    "expanded titanium metal load tables".

    Look at images on Google or big for tables of data.
  24. According to payscale_dot_com, average income for...

    According to payscale_dot_com, average income for Civil Engineers is $65,475 / year.

    2347

    keepacapearound00 -> how much do you think you should be earning?
  25. Home work not allowed.. Read the rules.

    Home work not allowed.. Read the rules.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4