Search:

Type: Posts; User: jboggs

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Job Hunting

    by jboggs
    Replies
    1
    Views
    130

    Speaking from the other end of the career road:...

    Speaking from the other end of the career road: Widen your options. Don't restrict yourself. There are LOTS more fields out there than aerospace. In fact, "aerospace engineering" could be...
  2. Replies
    5
    Views
    256

    As I suggested in the other forum in which you...

    As I suggested in the other forum in which you posted, buy a fully threaded bolt. They're available lots of places (McMaster. Fastenal) and are not expensive. No need to change anything, and its...
  3. Replies
    4
    Views
    403

    A picture is worth a thousand words. Post an...

    A picture is worth a thousand words. Post an image of your arrangement and forces. Your last statement just thoroughly confused me.

    If you install a bearing type that is rated for both radial...
  4. Replies
    3
    Views
    408

    Maybe you could use some of that money you're...

    Maybe you could use some of that money you're supposedly "saving" by having the work done in China to get in touch with a more local manufacturer who might cost more up front but would also feel some...
  5. Our city hosts an annual high school competitive...

    Our city hosts an annual high school competitive robotics competition as part of a worldwide program. As a long-time adult team mentor and chair of a local support group, I have been a frequent...
  6. Replies
    2
    Views
    887

    One of the many lessons from my decades of...

    One of the many lessons from my decades of engineering is this: Use set screws with caution. They are very often misused and end up damaging other components and failing.

    Look at your first...
  7. Replies
    10
    Views
    2,875

    I have been in machine design for over four...

    I have been in machine design for over four decades. I will admit there are a lot of things out there I am unfamiliar with, but I have never even heard of a so-called "coil thread". I am, however,...
  8. Replies
    2
    Views
    979

    I have dealt with a number of special bevel gears...

    I have dealt with a number of special bevel gears over the years, and I haven't seen any of your calculations. That said, my first impression of the picture is that whatever factors in your...
  9. Replies
    9
    Views
    921

    There are cabinet door hinges that do that. They...

    There are cabinet door hinges that do that. They connect the door to the frame in such a way that when the door opens it pivots about a centerline that is outside the physical boundary of the hinge...
  10. Replies
    9
    Views
    921

    I think your problem is probably the location of...

    I think your problem is probably the location of center of rotation. If the centerline of your pivot point is above the red floor then the bottom corners of the two opposed green shells are going to...
  11. Replies
    9
    Views
    921

    We might be able to help if you could draw it out...

    We might be able to help if you could draw it out to scale.
  12. Replies
    6
    Views
    831

    The drawing could use much improvement. Most of...

    The drawing could use much improvement. Most of the lines looked like object lines to me. None of them looked like hidden lines or tangent lines. Based on the arrangement of the lines in the left...
  13. Replies
    9
    Views
    921

    That's a very open-ended question with very...

    That's a very open-ended question with very little definition. What have you tried? Why didn't it work?
  14. Replies
    9
    Views
    921

    What is your question?

    What is your question?
  15. Replies
    6
    Views
    592

    Back in the day engineers used mechanical...

    Back in the day engineers used mechanical indexers to drive dial indexing tables for all kinds of automated assembly processes. I used Camco indexers on several successful projects. Like these:...
  16. I have no idea of the loads you are dealing with...

    I have no idea of the loads you are dealing with or the precision with which these carriages must move. Are the carts rolling on the floor now with no damage? If so, great! No need to over-think...
  17. Have you sized the wheels? If so, contact the...

    Have you sized the wheels? If so, contact the manufacturer's application engineer and get their recommendation on angle size etc. I would say as long as its fully supported on concrete over its...
  18. A few tips: 1 - You said the rails are fully...

    A few tips:
    1 - You said the rails are fully supported on a concrete floor, so I don't see where a bending analysis is even required.

    2 - The bending diagram you referenced is for a beam...
  19. Replies
    19
    Views
    1,237

    Well sorry, but the phrase "looking for an...

    Well sorry, but the phrase "looking for an element of patentable novelty" does seem to infer that one is desiring to achieve a patent. I'm trying to understand why one would intentionally not use a...
  20. Replies
    19
    Views
    1,237

    No need to remove yourself. Hang around. There...

    No need to remove yourself. Hang around. There is always more to learn.
  21. Replies
    19
    Views
    1,237

    What he said!

    What he said!
  22. Replies
    19
    Views
    1,237

    In a way you just answered some of your own...

    In a way you just answered some of your own questions. You said the instrument displays "Nm". That is a different animal than "N". One is a unit of force. The other a unit of torque. And there...
  23. Replies
    19
    Views
    1,237

    A force of 7N applied at the center is simply a...

    A force of 7N applied at the center is simply a force of 7N. Force has a linear direction and a single location. A rotary force is a torque. And torque is always expressed in terms of force @...
  24. Replies
    19
    Views
    1,237

    The key to failure analysis is to identify the...

    The key to failure analysis is to identify the very FIRST point of failure, the initial crack, and why it failed AT THAT POINT. Many times we find a "stress concentrator" at that point, usually in...
  25. Replies
    2
    Views
    1,762

    I don't understand your question - "How to...

    I don't understand your question - "How to machine it?".

    Are you saying you don't understand the machining steps involved to create the various parts? If that is the case then get advice from a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4