Search:

Type: Posts; User: Cragyon

Page 1 of 11 1 2 3 4

Search: Search took 0.00 seconds.

  1. Using Engineers Edge 2D Statics Modeler I get.. ...

    Using Engineers Edge 2D Statics Modeler I get..

    2529

    https://www.engineersedge.com/calculators/statics-modeler/statics-2d-modeling.htm#
  2. Replies
    1
    Views
    265

    Very creative! Use what you have design and...

    Very creative! Use what you have design and engineering at its best.
  3. Replies
    2
    Views
    530

    Every stress-strain plot I've seen was reported...

    Every stress-strain plot I've seen was reported in actual units. I don't think the strain is being report as a % but being converted into a multiple for ease of reading the plot.

    A note would...
  4. Probably using Profile of a Surface/line. See:...

    Probably using Profile of a Surface/line.

    See: https://www.engineersedge.com/catalog/product_info.php/products_id/656/
  5. Replies
    1
    Views
    558

    It's best to ask the asker which is "Underwriters...

    It's best to ask the asker which is "Underwriters Laboratory".

    Probably means size variations or number of wires/strands etc... Again, see sentence above.
  6. Replies
    1
    Views
    583

    Yes, rated stress of wood is dependent on loading...

    Yes, rated stress of wood is dependent on loading direction relative to grain. Loading perpendicular to grain will cause separate.

    Also, the stress strain curve is incomplete.
  7. Replies
    10
    Views
    2,471

    Looks like a ball screw thread. See bottom of...

    Looks like a ball screw thread.

    See bottom of this webpage: https://www.engineersedge.com/mechanics_machines/ball_screw_design_equations_15235.htm
  8. Replies
    2
    Views
    690

    Why would you even model it? Are you 3D printing...

    Why would you even model it? Are you 3D printing the gears?

    If machining, determine gear ratio, specify desired industry standard tooth profile, pitch or whatever diameter needed, AGMA tolerance...
  9. Replies
    3
    Views
    339

    Deep drawing or spinning.

    Deep drawing or spinning.
  10. Replies
    6
    Views
    358

    Retractable mechanical stop at 120 deg....

    Retractable mechanical stop at 120 deg. increments? Have you considered a programable stepper motor control electronics like Rambo board?
  11. Replies
    0
    Views
    329

    Hanging Chain = Parabola Proof

    Proof that a hanging chain fixed at both ends will have the shape of a parabola.
    2501
  12. Replies
    1
    Views
    332

    Unknown.... I suggest that your organization...

    Unknown.... I suggest that your organization obtain one of these problematic gears and develop a a strategy to better identify when these "bumps" occur and how.

    I would track tooling, machine...
  13. Replies
    19
    Views
    832

    You didn't understand or are antagonizing Kelly...

    You didn't understand or are antagonizing Kelly (which i don't recommend you do that)..

    If you want a product that WORKS don't waste time with non-engineered, new and not understood, existing...
  14. Replies
    19
    Views
    832

    Use industry standard splines, like from the...

    Use industry standard splines, like from the following. Predictable and understood.

    https://www.engineersedge.com/gears/involute_spline_and_serration__13650.htm
  15. Replies
    19
    Views
    832

    There are many - many plastics that can be 3D...

    There are many - many plastics that can be 3D printed. Like ABS, PLA Nylon - what the materials? Kelly seems to be using a crowbar to get useful information out you and still not getting what...
  16. Replies
    2
    Views
    1,680

    See "Theoretical Calculation and Analysis on the...

    See "Theoretical Calculation and Analysis on the Composite Rock-Bolt Bearing Structure in Burst-Prone Ground
    "

    2488
  17. Thread: Lead screws

    by Cragyon
    Replies
    3
    Views
    3,317

    Lead screw is just another word for a threaded...

    Lead screw is just another word for a threaded rod on a bearing. Also called a power screw, translation screw which translates rotation into linear motion.
  18. Replies
    1
    Views
    2,762

    Insufficient information to assist.

    Insufficient information to assist.
  19. I ~ think you're referring to a hydrostatic...

    I ~ think you're referring to a hydrostatic bearing application? The math model would take in consideration the oil groove geometry, supplied pressure, etc.. Ultimately a differential pressure test...
  20. Replies
    2
    Views
    3,285

    I searched the internet for "CA ventilation...

    I searched the internet for "CA ventilation requirements" and got....

    https://tinyurl.com/y233cgzq
  21. Replies
    1
    Views
    2,833

    Energy return = (Energy in) - (Energy absorbed)....

    Energy return = (Energy in) - (Energy absorbed).

    You need to estimate the Transmissibilty of the elastomer, then Natural Frequency and compare to application. This will give you an idea on the...
  22. Replies
    5
    Views
    1,988

    Winding left or right is irrelevant to function,...

    Winding left or right is irrelevant to function, the winding is to keep the rope or cable together when not under load. Whena load is placed on a rope, torque iscreated within the rope as wires...
  23. Replies
    2
    Views
    1,014

    Yes, you should contact the designer..... You're...

    Yes, you should contact the designer..... You're asking for a full analysis from an unrelated forum.
  24. Replies
    9
    Views
    680

    I'm with Kelly, how does a design cycle even work...

    I'm with Kelly, how does a design cycle even work when given a cross section image and nothing more?
  25. Replies
    1
    Views
    327

    Did you see this? API NUE Tubing Recommended...

    Did you see this?

    API NUE Tubing Recommended Torque Table

    https://www.engineersedge.com/fluid_flow/api_nue_tubing_recommended_torque_table_13209.htm
Results 1 to 25 of 259
Page 1 of 11 1 2 3 4