Products and Services Directory: engineering > Engineering Standards Specifications > ASTM International Standards Specifications

Prev Page | Next Page

Pages: << 2 3 4 [5] 6 7 8 >>

F467M-03a - Standard Specification for Nonferrous Nuts for General Use [Metric]

This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications.

 

F436-04 - Standard Specification for Hardened Steel Washers

This specification covers the chemical, mechanical, and dimensional requirements for hardened steel washers for use with fasteners having nominal thread diameters of 1/4 through 4 in. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners. These washers are suitable for use with fasteners covered in Specifications A 325, A 354, A 449, A 490, and A 687.

 

F436M-04 - Standard Specification for Hardened Steel Washers [Metric]

This specification covers the chemical, mechanical, and dimensional requirements for metric hardened steel washers for use with fasteners having nominal thread diameters M12 through M100. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners. These washers are suitable for use with fasteners covered in Specifications A 325M, A 490M, A 563M and with fasteners of Specification F 568 property classes 8.8 and higher.

 

F432-04 - Standard Specification for Roof and Rock Bolts and Accessories

This specification covers the chemical, mechanical, and dimensional requirements for roof and rock bolts and accessories. Addressed in this specification are double-end threaded and slotted steel bars; fully grouted bolts and threaded bars; mechanical anchorage devices used for point anchorage applications; roof truss systems; partially grouted deformed bolts; formable anchorage devices; and other frictional anchorage devices. All of these products represent various designs used for ground support systems. This specification can be revised to address new technologies.

 

A574M-04 - Standard Specification for Alloy Steel Socket-Head Cap Screws [Metric]

This specification covers the requirements for quenched and tempered alloy steel socket-head cap screws 1.6 mm through 48 mm in diameter having a minimum ultimate tensile strength of 1220 MPa.

 

A574-04 - Standard Specification for Alloy Steel Socket-Head Cap Screws

This specification covers the requirements for quenched and tempered alloy steel hexagon socket-head cap screws, 0.060 through 4 in. in diameter where high strength is required.

 

A563M-04 - Standard Specification for Carbon and Alloy Steel Nuts [Metric]

This specification covers chemical and mechanical requirements for eight property classes of hex and hex-flange carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other externally threaded parts.

 

A563-04a - Standard Specification for Carbon and Alloy Steel Nuts

This specification covers chemical and mechanical requirements for eight grades of carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other externally threaded parts.

 

A502-03 - Standard Specification for Rivets, Steel, Structural

This specification covers three grades of steel rivets in diameters from 1/2 to 1 1/2 in. inclusive, for structural fabricating purposes. The grades are as follows: 1 Carbon steel rivets for general purpose use 2 Carbon manganese steel rivets for use with high strength carbon and high strength low alloy structural steels 3 Weathering steel rivets

 

A490M-04a - Standard Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints [Metric]

This specification covers two types of quenched and tempered alloy steel, metric heavy hex structural bolts having a tensile strength of 1040 to 1210 MPa. The bolts are furnished in nominal bolt diameters M12 to M36, inclusive. They are designated by type denoting chemical composition as follows: Type 1 Medium carbon alloy steel  Type 2 Withdrawn in 2002  Type 3 Weathering steel

 

Prev Page | Next Page

Pages: << 2 3 4 [5] 6 7 8 >>

Contribute Article
Spider Optimizer

© Copyright 2000 - 2018, by Engineers Edge, LLC www.engineersedge.com
All rights reserved
Disclaimer | Feedback | Advertising | Contact

List Your Company HERE!! Add SEO Directory Listing | Advertising Information