Mechanical Design, Manufacturing and Engineering Forum
DFM DFA Training and Trainers | Engineering and Design Data | Product Services Directory | Advertise
Engineering Forum | Engineering Specifications Forum |
Engineering and Drafting Store | ASME Y14.5M - 1994 GD&T Training
POSTING POLICY / RULES | Archive#1 | Archive #2 | Archive #3 | Calculators

Forum Moderators: Administrator

Request for recommendation for minature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion Question
Post Reply   Forum
Posted by: john2003 ®

08/24/2005, 00:49:10

Author Profile Mail author Edit
Hello everyone,

I am hoping someone can help me find a suitable sleeve bushing material for a product I am developing. I am having a heck of a time finding something that looks like it will wear well and be reliable.

I need a plain sleeve bushing that will be self lubricating and provide good life in a slow moving, intermittently oscillating application, where the bushing rocks back and forth very slowly and intermittently.

The bushing ID is 1/8" and the bushing OD is 3/16". I am using the bushing as a small cam-follower roller. The cam is rotated by hand via a small lever, so the motion is very slow and intermittent. However, the loads are fairly high for such a small bushing, and with the oscillating movement, and the fact that the bushing cannot be lubricated, I am worried about wear. I want the product to be maintenance free and provide years of service.

The maximum load on the bushing will be 7,168 PSI, plus I guess I should have some type of small safety factor. The average sweep angle will be about 9 degrees, at an average speed of about 1 to 3 Hz. I think the average surface speed would be 0.2 to a maximum of 0.4 FPM. The device will always be operated at room temperature, and be in a very clean household environment with no dust or dirt. There is also no chemical exposure. The bushing will rotate on a hardened dowel pin meeting ASME B18.8.2 standards, I can either use plain ground finish, or black oxide finish. I could also go with a 303 stainless shaft if needed. In this application as a cam-follower, the bushing oscillates on a stationary shaft. I could put a small amount of lube on the bushing at assembly, but never again after that point.

The motion will always last for only a few seconds and then stop. It may last 1-3 seconds on average, say two or three times per minute, and then the rest the time the device is at a standstill, with a static load on the bushing, of about 4,266 PSI, which could also be considered the “average” bushing load, but the maximum will be 7,168 PSI. The load changes as the cam is rotated. It might be used intermittently, for a "total" of about 36 minutes per day, ( i.e., the device is activated a few seconds at a time, a few times per minute, adding up to 36 minutes of total intermittent start / stop use, over the course of around 3 hours, each day).

I won’t need much running clearance, since the device always operates at room temperature, and since heat from friction will not be enough to cause any significant dimensional changes to the bushing, the speeds are too slow and intermittent. However, I would like to keep the maximum clearance between the bushing ID and the shaft at .004” or less. So, if I start out at a clearance of .003”, this only gives me .001” for wear. Maybe I could get away with .002” of wear for a maximum clearance of .005”, but I am not sure. Ideally, I need something that can provide years of service, with very low wear rates.

I tried some plastic bushings from www.igus.com, but found that they were so slippery, that there was sliding between the cam and the bushing OD. This caused the cam to wear a flat spot on the bushing OD. I then tried the "FB" series bushings from www.peerinc.com, but since they are a wrapped or spit bushing, it seems when the bushing seam lines up with the cam, the cam spreads the bushing apart at the seam. Plus the seam causes a little noice, and bumpiness.

I thought of pressing the above mentioned bushings into a steel tube, to solve the aforementioned problems, but then the bushing OD becomes about 1/4". I am working in such a confined space, that I cannot really make the cam any smaller at all, because the minimum radius of curvature becomes to small. Therefore, I really need to stay with a bushing that has a 3/16" OD.

I also thought of putting some “belt dressing” https://www.lpslabs.com/Products/Lubricants/Belt_Dressing.asp on the plastic bushing OD, to insure that the friction between the cam and roller OD is always greater than the friction between the roller ID & shaft, in order to eliminate sliding between the cam and bushing OD, but I just don’t know how long it would last, and I need the product to be maintenance free.

Since the plastic bushings seem to be to slippery on the OD, and I cannot press them into a metal tube to make the OD less slippery, since the OD will then be too big, I figure I must need some type of metal roller.

I have not been able to find a stock bushing that meets the requirements, so I am hoping someone can recommend a bushing material I can machine or fabricate the bushings from.

I am thinking of trying to use some 3/16" OD drill rod from www.mcmaster.com for this roller. It's held to close OD tolerance, and I can just cut to length and drill the center hole out. I could then lube it once, and put it in service.

Would drill rod provide both the needed load capacity and decent wear resistance ? Perhaps I can shoot for .001" or .002" running clearance, and then that will leave at least .002" for wear. Do you think I could get a decent service life ?

I will be using a standard 1/8" OD hardened dowel pin as the bushing shaft.

I can get the drill rod in A2, D2, M-2, 0-1, S-7,or W-1. Which grade would be best ? I am thinking of using W-1.

What type of lube would you recommend ? I can only lube once at assembly, and then never again. I guess the ideal lube would be a high pressure lube that is good for pivoting motion, and that will stay in place, and last. I also have to be careful not to get any on the bushing OD.

Would a dowel having a black oxide finish help at all, since black oxide has lubricating properties, and it could possibly help retain lube ?

Lastly, would this be just about as quiet as a standard bronze bushing ?

Please let me know what you guys think, I would appreciate any advice or comments from anyone. Perhaps someone at the forum has had experience with a steel bushing oscillating on a hardened shaft.

I would really appreciate any advice anyone might have.

Thanks for your help.

Sincerely,
John







Post Reply | Recommend | Alert View All   | Next |

Replies to this message


Re: Request for recommendation for minature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion
Re: Request for recommendation for minature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion -- john2003 Post Reply Top of thread Forum
Posted by: randykimball ®
Barney
08/24/2005, 20:20:08

Author Profile Mail author Edit
A surface hardening process that may work well here in the ID and on the OD is Armoloy. This is a type of hard chrome process that applies a more pure and very high percent of chrome and ends up at a Rockwell hardness of around 70. It is used often in food service dies and wears great. Armoloy doesn't build up as high as other plating process and is claimed to impregnate the surface molucules. We used it plenty back in the 70's and it out lasted the equipment as I remember. I'd suggest 4140 heat treated up in the mid 50's rockwell as a substrate. I'd say it wears like iron, but it wears much better..... big smile. A2 or D2 drill rod heat treated would work fine too.

-randy-




The worst suggestion of your lifetime may be the catalyst to the grandest idea of the century, never let suggestions go unsaid nor fail to listen to them.

Modified by randykimball at Wed, Aug 24, 2005, 20:24:14

Post Reply | Recommend | Alert Where am I? Original Top of thread
Re: Request for recommendation for minature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion
Re: Request for recommendation for minature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion -- john2003 Post Reply Top of thread Forum
Posted by: john2003 ®

08/24/2005, 13:11:51

Author Profile Mail author Edit
Hi everyone,

Correction to post:

The average sweep angle for the bushing is 42.25 degrees, not 9, and the average surface speed would be around 0.46 to 1.4 FPM. I got my figures mixed up. Everything else in the post is correct.

The device will probably have an average "turn on" time of 3 seconds, and an average rest period of 27 seconds. If it's activated an average of 3 times per minute it will be used for 9 minutes total per hour, for 3 hours per day. If I can get 1,642 hours of life, the product will last 10 years.

Thanks for your help.

John







Post Reply | Recommend | Alert Where am I? Original Top of thread | |
Re: Request for recommendation for minature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion Smile
Re: Re: Request for recommendation for minature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion -- john2003 Post Reply Top of thread Forum
Posted by: Gary Kemp ® garykemp

08/24/2005, 13:31:49

Author Profile Mail author Edit
If the item comes in contact with food there may be additional restrictions (seals etc.) I would consider a hardened drill bushing as a roller. You can order them to an exact dimension. One method I have seen for lubricating a similar item is to machine a key slot for a blind key radiused on both ends and shorter than the bushing. Fill the slot with felt that has been permeated with grease and cut to fit the slot. It should stay lubricated for a long time.






Post Reply | Recommend | Alert Where am I? Original Top of thread | |
Re: Request for recommendation for miniature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion
Re: Re: Request for recommendation for minature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion -- Gary Kemp Post Reply Top of thread Forum
Posted by: john2003 ®

08/24/2005, 14:08:11

Author Profile Mail author Edit
Hi Gary,

Thanks for your reply.

You recommended a hardened drill bushing, but should I be using a hardened drill bushing on a hardened shaft ? The dowel pin is RC 60 with a surface finish of 8 micro-inch or better.

As I understand it, one surface should be hard and the other should be softer in order to reduce wear and galling.

I might be able to machine a slot into the hardened dowel pin with a miniature grinding wheel, to put the greased felt in. That seems like a good idea, but It's just a matter of doing it on such small parts. I could go to a softer shaft if needed, say 303 stainless or something.

Would using drill-rod as a bushing on a hardened shaft be viable ?

Please let me know if you have any other comments.

Thanks
John







Post Reply | Recommend | Alert Where am I? Original Top of thread | |
Re: Request for recommendation for miniature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion Smile
Re: Re: Request for recommendation for miniature plane sleeve bushing material used in slow, intermittent, oscillating and/or pivoting motion -- john2003 Post Reply Top of thread Forum
Posted by: Gary Kemp ® garykemp

08/24/2005, 15:43:12

Author Profile Mail author Edit
The hardened bushing will ensure minimum risk of wearing a flat on the o.d. as you described. I would make the shaft from 4340 or 4130 and harden and finish grind the dia after machining the slot and ht to rc 46-52. I wouldn't anticipate a galling issue. I think loss of lube is still the biggest challenge without seals. I have no problem with drill rod as a roller, I just wouldn't make a bushing if I could buy it. A hundred guys would probably do it a hundred different ways and most of them would do ok. Sometimes personal preference comes into play from successes.






Post Reply | Recommend | Alert Where am I? Original Top of thread

Powered by Engineers Edge

© Copyright 2000 - 2024, by Engineers Edge, LLC All rights reserved.  Disclaimer