Page 56 of 86 FirstFirst ... 6 46 54 55 56 57 58 66 ... LastLast
Threads 1101 to 1120 of 1718

Forum: Engineering and Design Main Forum

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 20,303
    petronextinternational
    11-15-2018, 12:07 AM Go to last post

  1. Beam Weld Joint Hurry

    Started by Dominguez Mexico, 08-26-2013 10:14 AM
    1 Attachment(s)
    • Replies: 3
    • Views: 3,839
    Cragyon
    08-29-2013, 12:17 PM Go to last post

  2. Engineers Club Buy and Sell is Now Free

    Started by administrator, 08-29-2013 07:58 AM
    • Replies: 0
    • Views: 3,117
    administrator
    08-29-2013, 07:58 AM Go to last post

  3. Permanent magnet and electric magnet repulsion and attraction

    Started by PRT, 08-20-2013 01:46 PM
    • Replies: 1
    • Views: 3,664
    JAlberts
    08-25-2013, 02:21 PM Go to last post

  4. Steampunk Air Ship

    Started by Yuki, 08-18-2013 11:19 PM
    airship steampunk
    • Replies: 3
    • Views: 3,402
    Kelly_Bramble
    08-22-2013, 08:57 AM Go to last post

  5. ID change due to heating on a press fit polymer bearing

    Started by RStakely, 08-20-2013 09:34 AM
    bearing, interference, thermal growth
    • Replies: 4
    • Views: 4,814
    Kelly_Bramble
    08-22-2013, 07:44 AM Go to last post

  6. Section Modulus Help

    Started by LUGO331, 07-18-2013 06:10 PM
    • Replies: 6
    • Views: 6,398
    kjoiner
    08-19-2013, 08:25 AM Go to last post

  7. Is it possible to calcuate this?

    Started by peteinsg, 08-15-2013 12:19 PM
    • Replies: 4
    • Views: 5,292
    kjoiner
    08-19-2013, 07:21 AM Go to last post

  8. Post Strength of Steel

    Started by DCA, 08-16-2013 09:29 AM
    3 Attachment(s)
    • Replies: 1
    • Views: 3,087
    Kelly_Bramble
    08-17-2013, 04:03 PM Go to last post

  9. need help with heat transfer problem. urgent

    Started by whlock, 08-16-2013 11:55 AM
    • Replies: 1
    • Views: 3,224
    whlock
    08-16-2013, 03:42 PM Go to last post

  10. liquid ring vacuum pump

    Started by canbanucan, 08-15-2013 01:46 AM
    • Replies: 2
    • Views: 3,109
    canbanucan
    08-15-2013, 08:29 AM Go to last post

  11. Have any of you taken the patent bar exam?

    Started by AzBigE, 04-26-2013 08:43 PM
    patent
    • Replies: 7
    • Views: 7,332
    lancevincent
    08-14-2013, 06:32 AM Go to last post

  12. Mini Hydraulic Press

    Started by Hans, 02-12-2012 06:16 AM
    • Replies: 8
    • Views: 7,963
    inder123
    08-08-2013, 11:24 PM Go to last post

  13. Heat Plate in Air to Melt Plastic

    Started by rjsfocus, 08-06-2013 08:25 PM
    • Replies: 3
    • Views: 3,532
    Kelly_Bramble
    08-08-2013, 04:25 PM Go to last post

  14. Which of these poses more of a software and hardware engineering challenge?

    Started by Enginterest, 08-05-2013 03:13 AM
    • Replies: 2
    • Views: 3,092
    Kelly_Bramble
    08-06-2013, 01:00 PM Go to last post

  15. Buckling Strenth of pipe with non-axial load

    Started by sudnak, 08-01-2013 05:16 PM
    2 Attachment(s)
    • Replies: 1
    • Views: 3,911
    Kelly_Bramble
    08-01-2013, 09:03 PM Go to last post

  16. Help with nomenclature?

    Started by CCR5600Design, 07-26-2013 12:40 PM
    • Replies: 2
    • Views: 3,358
    CCR5600Design
    08-01-2013, 08:20 AM Go to last post

  17. Flip Flop circuits

    Started by soulinfinity, 08-01-2013 07:12 AM
    flip flop
    • Replies: 1
    • Views: 7,411
    Cragyon
    08-01-2013, 08:17 AM Go to last post

  18. Slow Motion of an AK-47 Underwater Part 1

    Started by Kelly_Bramble, 07-30-2013 08:57 PM
    • Replies: 1
    • Views: 2,976
    Kelly_Bramble
    07-31-2013, 08:23 AM Go to last post

  19. device to let air out but not water under pressure

    Started by user001, 07-23-2013 12:24 PM
    • Replies: 2
    • Views: 3,849
    PinkertonD
    07-23-2013, 04:44 PM Go to last post

  20. Threaded Insert or Not

    Started by Killroy, 06-27-2013 11:29 AM
    1 Attachment(s)
    • Replies: 9
    • Views: 5,316
    RWOLFEJR
    07-23-2013, 12:37 PM Go to last post
Page 56 of 86 FirstFirst ... 6 46 54 55 56 57 58 66 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules