Page 13 of 86 FirstFirst ... 3 11 12 13 14 15 23 63 ... LastLast
Threads 241 to 260 of 1718

Forum: Engineering and Design Main Forum

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 19,304
    petronextinternational
    11-15-2018, 12:07 AM Go to last post

  1. Air Pressure

    Started by richardgrant, 03-19-2011 07:09 PM
    • Replies: 6
    • Views: 6,894
    PinkertonD
    03-27-2011, 10:39 AM Go to last post

  2. Hey Kelly, What's in a Percentage??

    Started by PinkertonD, 10-31-2011 03:26 PM
    • Replies: 6
    • Views: 4,627
    PinkertonD
    10-31-2011, 09:02 PM Go to last post

  3. standards/masters

    Started by NeelyDummi, 11-08-2011 02:51 AM
    • Replies: 6
    • Views: 4,284
    Kelly_Bramble
    11-08-2011, 07:44 PM Go to last post

  4. Time out accessing the Edge...

    Started by PinkertonD, 04-19-2012 11:15 AM
    • Replies: 6
    • Views: 4,228
    PinkertonD
    04-20-2012, 05:11 PM Go to last post

  5. Calculate welding strength?

    Started by projektshare, 05-30-2017 10:33 AM
    2 Attachment(s)
    • Replies: 6
    • Views: 3,609
    jboggs
    05-31-2017, 06:42 AM Go to last post

  6. Need advice and guidance

    Started by hobby welder, 06-12-2013 09:28 PM
    • Replies: 6
    • Views: 3,325
    RWOLFEJR
    06-14-2013, 07:57 AM Go to last post

  7. Pushing water along.

    Started by Gravity, 11-22-2013 05:22 AM
    • Replies: 6
    • Views: 3,126
    JAlberts
    11-25-2013, 02:51 PM Go to last post

  8. Infrared Drying for firecrackers. Possible?

    Started by supersonics29, 11-29-2013 06:11 AM
    • Replies: 6
    • Views: 3,331
    dalecyr
    12-12-2013, 12:18 PM Go to last post

  9. Accelerating a ball bearing around a track using electromagnet

    Started by d4rr3n, 12-15-2013 09:51 AM
    1 Attachment(s)
    • Replies: 6
    • Views: 4,693
    JAlberts
    12-17-2013, 11:57 AM Go to last post

  10. Ideas on how to calculate the volume of a telescoping assembly.

    Started by ENGR, 04-07-2014 05:53 PM
    1 Attachment(s)
    • Replies: 6
    • Views: 3,605
    fredapinto164
    04-21-2014, 07:45 AM Go to last post

  11. Alternators in car wheels

    Started by die247, 04-13-2014 03:10 PM
    • Replies: 6
    • Views: 5,363
    die247
    04-16-2014, 03:38 PM Go to last post

  12. Heated pannier

    Started by jazzman, 05-05-2014 07:37 AM
    1 Attachment(s)
    • Replies: 6
    • Views: 2,995
    jazzman
    05-07-2014, 03:31 AM Go to last post

  13. Smile Need help in finishing up a parabolic solar hot water heater

    Started by frazelle09, 05-18-2014 08:52 PM
    hot water, parabolic, solar, sustainability 2 Attachment(s)
    • Replies: 6
    • Views: 3,238
    GlennD
    05-27-2014, 01:37 PM Go to last post

  14. Axial Flow Fan Selection

    Started by CJS, 08-18-2014 06:59 AM
    • Replies: 6
    • Views: 2,827
    CJS
    08-19-2014, 03:07 AM Go to last post

  15. Converting newtons to lbs. per inch

    Started by frankroger, 10-20-2014 12:33 PM
    force, newtons, pounds per inch, springs
    • Replies: 6
    • Views: 4,222
    frankroger
    10-21-2014, 06:07 PM Go to last post

  16. Question(s) about Torque-to-yield bolts (engine rod bolts)

    Started by byghtn, 03-24-2015 12:41 AM
    • Replies: 6
    • Views: 16,713
    byghtn
    03-25-2015, 09:24 PM Go to last post

  17. Design and engineering

    Started by ap91, 10-07-2015 10:10 PM
    • Replies: 6
    • Views: 3,153
    Hudson
    10-19-2015, 11:26 PM Go to last post

  18. Attic Floor Joist Sistering Options

    Started by ellisadamm, 12-05-2016 08:05 PM
    attic, conversion, joist, sistering, span
    • Replies: 6
    • Views: 4,916
    Hudson
    12-09-2016, 01:12 PM Go to last post

  19. Basic Statics Question - Loads at angles

    Started by larsen4, 03-24-2017 09:04 PM
    2 Attachment(s)
    • Replies: 6
    • Views: 3,575
    larsen4
    04-01-2017, 12:19 PM Go to last post

  20. Cutting 1060 plate

    Started by rmeyer, 01-04-2019 08:42 AM
    1060, plasma cutting
    • Replies: 6
    • Views: 4,647
    petronextinternational
    02-09-2019, 02:58 AM Go to last post
Page 13 of 86 FirstFirst ... 3 11 12 13 14 15 23 63 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules