Page 77 of 86 FirstFirst ... 27 67 75 76 77 78 79 ... LastLast
Threads 1521 to 1540 of 1718

Forum: Engineering and Design Main Forum

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 19,705
    petronextinternational
    11-15-2018, 12:07 AM Go to last post

  1. Drop shock calculation

    Started by buberiko, 07-12-2018 02:55 AM
    drop shock calculation
    • Replies: 0
    • Views: 2,483
    buberiko
    07-12-2018, 02:55 AM Go to last post

  2. Load capacity of a homemade jib crane

    Started by mike_sou, 07-11-2022 04:51 PM
    1 Attachment(s)
    • Replies: 1
    • Views: 2,480
    Kelly_Bramble
    07-12-2022, 01:27 PM Go to last post

  3. Fastener hardness, threads vs shank

    Started by pmarshall, 04-18-2017 11:50 AM
    • Replies: 3
    • Views: 2,479
    JAlberts
    04-20-2017, 11:00 AM Go to last post

  4. Screw torque specs

    Started by steve_fyten, 09-09-2021 09:39 AM
    • Replies: 1
    • Views: 2,479
    Kelly_Bramble
    09-09-2021, 10:17 AM Go to last post

  5. Cat wheel

    Started by corbett, 07-04-2022 09:20 AM
    1 Attachment(s)
    • Replies: 5
    • Views: 2,479
    jboggs
    07-06-2022, 09:04 AM Go to last post

  6. Practical Engineering Projects

    Started by jwildm, 10-26-2021 08:10 AM
    • Replies: 3
    • Views: 2,477
    alievserega17
    11-30-2021, 11:06 PM Go to last post

  7. Shaft - Spring retainer

    Started by freddy15, 03-09-2015 08:28 PM
    2 Attachment(s)
    • Replies: 1
    • Views: 2,476
    jboggs
    03-10-2015, 07:38 AM Go to last post

  8. Tool to Apply a Radial Force on Tubes

    Started by Mr. Engineer, 05-17-2015 03:41 PM
    • Replies: 1
    • Views: 2,476
    Kelly_Bramble
    05-18-2015, 07:17 AM Go to last post

  9. chain drive over a gear drive

    Started by nimesh_rakholiya, 01-29-2017 02:48 AM
    • Replies: 3
    • Views: 2,476
    Kelly_Bramble
    01-29-2017, 08:29 AM Go to last post

  10. Hardening factor or exponent

    Started by ManuThimlapura, 02-05-2015 05:23 AM
    • Replies: 0
    • Views: 2,473
    ManuThimlapura
    02-05-2015, 05:23 AM Go to last post

  11. Clip that will release under load?

    Started by Researcher, 05-14-2015 08:58 AM
    • Replies: 0
    • Views: 2,473
    Researcher
    05-14-2015, 08:58 AM Go to last post

  12. Limit Gauge Question

    Started by daveajohnsonou, 07-19-2018 02:26 PM
    • Replies: 0
    • Views: 2,472
    daveajohnsonou
    07-19-2018, 02:26 PM Go to last post

  13. Selection of hydraulic pump

    Started by m6957341, 04-20-2022 04:55 AM
    1 Attachment(s)
    • Replies: 10
    • Views: 2,472
    m6957341
    04-28-2022, 06:03 AM Go to last post

  14. UT data taken during on-stream vs shutdown - the difference?

    Started by khaiis, 01-14-2015 04:59 AM
    • Replies: 1
    • Views: 2,470
    JAlberts
    01-16-2015, 10:12 AM Go to last post

  15. Controlled Descender HELPPPPP

    Started by al_garnett, 02-05-2015 06:43 AM
    • Replies: 0
    • Views: 2,469
    al_garnett
    02-05-2015, 06:43 AM Go to last post

  16. What To Look For When Hiring A Structural Engineer?

    Started by vectorseo1, 09-08-2021 06:59 AM
    structural engineer
    • Replies: 2
    • Views: 2,469
    vectorseo1
    09-14-2021, 09:08 AM Go to last post

  17. Static Mixing Improvements for Disposables

    Started by ArgoMix, 07-23-2015 12:57 PM
    disposable, mix, mixer, static, waste reduction
    • Replies: 0
    • Views: 2,468
    ArgoMix
    07-23-2015, 12:57 PM Go to last post

  18. Heated pannier

    Started by jazz, 04-07-2014 10:02 AM
    • Replies: 0
    • Views: 2,467
    jazz
    04-07-2014, 10:02 AM Go to last post

  19. Need help with project

    Started by Juggernaut12121, 11-16-2014 03:04 PM
    • Replies: 0
    • Views: 2,467
    Juggernaut12121
    11-16-2014, 03:04 PM Go to last post

  20. Determination of load cycle for automobile bearing

    Started by mani_boda, 01-19-2020 12:29 AM
    • Replies: 0
    • Views: 2,467
    mani_boda
    01-19-2020, 12:29 AM Go to last post
Page 77 of 86 FirstFirst ... 27 67 75 76 77 78 79 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules