Page 12 of 86 FirstFirst ... 2 10 11 12 13 14 22 62 ... LastLast
Threads 221 to 240 of 1719

Forum: Engineering and Design Main Forum

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 20,418
    petronextinternational
    11-15-2018, 12:07 AM Go to last post

  1. Confused Identifying a force

    Started by laster, 11-28-2019 07:19 AM
    1 Attachment(s)
    • Replies: 6
    • Views: 3,808
    Hudson
    11-29-2019, 02:35 PM Go to last post

  2. Designing of a baler machine

    Started by intexception, 11-29-2019 12:58 PM
    • Replies: 0
    • Views: 3,084
    intexception
    11-29-2019, 12:58 PM Go to last post

  3. Tank Considerations: Pressure vs Vacuum.

    Started by eddycurr, 11-26-2019 12:07 PM
    • Replies: 3
    • Views: 3,675
    eddycurr
    11-28-2019, 12:45 PM Go to last post

  4. identifying proper motor

    Started by mikdandn, 11-27-2019 06:58 AM
    • Replies: 3
    • Views: 2,939
    Hudson
    11-28-2019, 10:50 AM Go to last post

  5. How do you like Design Engineering?

    Started by bernalfernas303, 11-26-2019 05:04 AM
    • Replies: 1
    • Views: 2,888
    jboggs
    11-26-2019, 03:00 PM Go to last post

  6. Concentric Rings with constraints

    Started by flint59, 11-15-2019 04:24 PM
    seg
    • Replies: 0
    • Views: 3,062
    flint59
    11-15-2019, 04:24 PM Go to last post

  7. transmission project

    Started by rreye102, 11-09-2019 04:21 PM
    • Replies: 0
    • Views: 3,256
    rreye102
    11-09-2019, 04:21 PM Go to last post

  8. Learning about turbines and thinking about the output.

    Started by nnelson, 11-03-2019 04:55 PM
    turbine blades
    • Replies: 2
    • Views: 3,319
    nnelson
    11-03-2019, 08:02 PM Go to last post

  9. Rule of thumb strength question. Brass vs stainless steel

    Started by YorkshireDave1, 10-28-2019 11:04 AM
    brass, rotation, stainless, strength of materials
    • Replies: 2
    • Views: 4,107
    YorkshireDave
    10-28-2019, 11:51 AM Go to last post

  10. Best spline type - rotational force into plastic

    Started by YorkshireDave1, 10-28-2019 11:43 AM
    1 Attachment(s)
    • Replies: 0
    • Views: 3,125
    YorkshireDave
    10-28-2019, 11:43 AM Go to last post

  11. Rule of thumb for drilling holes in I beam flange

    Started by daleacyr, 10-23-2019 06:30 PM
    2 Attachment(s)
    • Replies: 3
    • Views: 19,246
    Kelly_Bramble
    10-24-2019, 12:16 PM Go to last post

  12. Motor with brake and gearbox for high torque application

    Started by bob_wolfe, 10-07-2019 11:00 AM
    • Replies: 1
    • Views: 3,734
    administrator
    10-07-2019, 01:07 PM Go to last post

  13. what kind of electric motor with reducer is needed?

    Started by gaizutisd, 10-04-2019 06:16 AM
    1 Attachment(s)
    • Replies: 0
    • Views: 3,113
    gaizutisd
    10-04-2019, 06:16 AM Go to last post

  14. Motor and Gearbox Pairing

    Started by darrell_gray, 09-18-2019 01:39 AM
    • Replies: 2
    • Views: 3,641
    darrell_gray
    09-25-2019, 02:24 AM Go to last post

  15. Deflection and Stress of arm with an angle

    Started by Enchantedhorses, 09-23-2019 10:33 AM
    • Replies: 1
    • Views: 3,342
    Cragyon
    09-23-2019, 08:42 PM Go to last post

  16. Tempered glass "burst" calculation

    Started by ezetom, 09-23-2019 09:54 AM
    • Replies: 0
    • Views: 2,964
    ezetom
    09-23-2019, 09:54 AM Go to last post

  17. Stainless steel floor drain

    Started by iamdemberedingtonsbodygaurd, 09-11-2019 10:48 AM
    • Replies: 4
    • Views: 4,432
    YorkshireDave
    09-22-2019, 10:49 AM Go to last post

  18. Back yard jet engine?

    Started by iamramondreddington, 09-12-2019 07:46 AM
    • Replies: 1
    • Views: 3,742
    Cragyon
    09-19-2019, 02:16 PM Go to last post

  19. Structural safe loading calculation

    Started by sdubey, 09-18-2019 09:36 PM
    • Replies: 1
    • Views: 3,887
    Cake of Doom
    09-19-2019, 04:13 AM Go to last post

  20. Physical height calculation of RA surface finishes.

    Started by billing, 09-16-2019 11:46 AM
    calculator, formula, ran, rms, surface finish
    • Replies: 1
    • Views: 3,773
    Kelly_Bramble
    09-16-2019, 02:29 PM Go to last post
Page 12 of 86 FirstFirst ... 2 10 11 12 13 14 22 62 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules