Page 1 of 75 1 2 3 11 51 ... LastLast
Threads 1 to 20 of 1492

Forum: Engineering and Design Main Forum | Engineers Edge Forums

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 9,104
    11-15-2018, 12:07 AM Go to last post
  1. Back yard jet engine?

    Started by iamramondreddington, 09-12-2019 07:46 AM
    • Replies: 0
    • Views: 140
    09-12-2019, 07:46 AM Go to last post
  2. Stainless steel floor drain

    Started by iamdemberedingtonsbodygaurd, 09-11-2019 10:48 AM
    • Replies: 2
    • Views: 199
    09-11-2019, 06:00 PM Go to last post
  3. Lever arm design

    Started by lavdesesamajmeayakya, 08-30-2019 06:42 AM
    • Replies: 2
    • Views: 514
    09-05-2019, 02:18 PM Go to last post
  4. Pneumatic hammer prototype

    Started by cjccmc, 08-30-2019 03:23 PM
    • Replies: 1
    • Views: 479
    09-03-2019, 12:45 PM Go to last post
  5. Pre-load on needle roller clutch

    Started by csendegeya, 08-30-2019 09:35 AM
    bearings, clutch
    • Replies: 1
    • Views: 443
    08-30-2019, 10:21 AM Go to last post
  6. Angle Iron Stress

    Started by komet99, 04-03-2012 09:48 PM
    • Replies: 9
    • Views: 65,911
    08-28-2019, 01:31 PM Go to last post
  7. Heat Exchanger Question

    Started by belachavbelachavchavchavchav, 08-22-2019 03:14 PM
    • Replies: 1
    • Views: 566
    08-23-2019, 08:27 AM Go to last post
  8. Uni project Help

    Started by Prialen08, 08-21-2019 09:41 AM
    design, jockey wheel
    • Replies: 0
    • Views: 505
    08-21-2019, 09:41 AM Go to last post
  9. Low Friction Fabrics

    Started by benjamin_banks, 05-01-2019 12:51 AM
    fabric, fashion, friction, material, science
    • Replies: 5
    • Views: 1,102
    08-15-2019, 10:41 AM Go to last post
  10. Ways to lessen wear caused by a steel fixture

    Started by harrisonczaj, 07-15-2019 10:47 AM
    fixture design, part wear, plastic coating
    • Replies: 5
    • Views: 894
    08-15-2019, 10:38 AM Go to last post
  11. SolidWorks Stress Analysis question

    Started by thinds, 08-12-2019 10:50 AM
    • Replies: 2
    • Views: 505
    08-13-2019, 08:10 AM Go to last post
  12. Material "Slash sheet description"

    Started by sdicarlo, 07-31-2019 02:41 PM
    • Replies: 0
    • Views: 371
    07-31-2019, 02:41 PM Go to last post
  13. Question tolerances, machining and cost

    Started by Ayien, 01-17-2018 07:23 PM
    gd&t, tolerances
    • Replies: 5
    • Views: 1,147
    07-29-2019, 01:16 PM Go to last post
  14. Aluminum on plastic tolerance fit?

    Started by sebastian_thomas, 04-29-2018 02:05 PM
    • Replies: 1
    • Views: 938
    07-29-2019, 01:10 PM Go to last post
  15. Need for advice

    Started by boutheynamzoughui, 07-29-2019 04:40 AM
    • Replies: 1
    • Views: 411
    07-29-2019, 07:20 AM Go to last post
  16. Air tanks in parallel and series

    Started by rouncer81, 07-26-2019 05:04 PM
    • Replies: 2
    • Views: 450
    07-26-2019, 05:38 PM Go to last post
  17. Reference for Table

    Started by halstedj, 07-26-2019 12:06 AM
    reference, source, table, thermal properties
    • Replies: 1
    • Views: 451
    07-26-2019, 07:21 AM Go to last post
  18. Red face Plastics Shredder Design

    Started by ramadhankd, 07-20-2019 08:19 AM
    calculation, invention, mechanical design, plastic, recycle
    • Replies: 1
    • Views: 657
    07-20-2019, 04:27 PM Go to last post
  19. Confused Help Plz!!! Scissor Lift, need help.

    Started by jw102033, 07-05-2019 10:07 AM
    • Replies: 0
    • Views: 933
    07-05-2019, 10:07 AM Go to last post
    • Replies: 2
    • Views: 1,873
    06-18-2019, 12:16 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •