Page 1 of 75 1 2 3 11 51 ... LastLast
Threads 1 to 20 of 1500

Forum: Engineering and Design Main Forum | Engineers Edge Forums

General engineering, design and manufacturing and related industry questions.

  1. Sticky Thread Sticky: No Homework! Read More Here

    Started by administrator, 03-30-2014 02:46 PM
    • Replies: 10
    • Views: 9,156
    11-15-2018, 12:07 AM Go to last post
  1. Machinery's, Roark's Stress and Strain, etc.

    Started by Kelly Bramble, 10-10-2019 08:04 AM
    • Replies: 2
    • Views: 129
    10-11-2019, 03:48 AM Go to last post
    • Replies: 1
    • Views: 239
    10-07-2019, 01:07 PM Go to last post
    • Replies: 0
    • Views: 209
    10-04-2019, 06:16 AM Go to last post
  2. Motor and Gearbox Pairing

    Started by darrell_gray, 09-18-2019 01:39 AM
    • Replies: 2
    • Views: 498
    09-25-2019, 02:24 AM Go to last post
  3. Deflection and Stress of arm with an angle

    Started by Enchantedhorses, 09-23-2019 10:33 AM
    • Replies: 1
    • Views: 380
    09-23-2019, 08:42 PM Go to last post
  4. Tempered glass "burst" calculation

    Started by ezetom, 09-23-2019 09:54 AM
    • Replies: 0
    • Views: 287
    09-23-2019, 09:54 AM Go to last post
  5. Stainless steel floor drain

    Started by iamdemberedingtonsbodygaurd, 09-11-2019 10:48 AM
    • Replies: 4
    • Views: 743
    09-22-2019, 10:49 AM Go to last post
  6. Back yard jet engine?

    Started by iamramondreddington, 09-12-2019 07:46 AM
    • Replies: 1
    • Views: 636
    09-19-2019, 02:16 PM Go to last post
  7. Structural safe loading calculation

    Started by sdubey, 09-18-2019 09:36 PM
    • Replies: 1
    • Views: 438
    09-19-2019, 04:13 AM Go to last post
    • Replies: 1
    • Views: 506
    09-16-2019, 02:29 PM Go to last post
  8. Lever arm design

    Started by lavdesesamajmeayakya, 08-30-2019 06:42 AM
    • Replies: 2
    • Views: 795
    09-05-2019, 02:18 PM Go to last post
  9. Pneumatic hammer prototype

    Started by cjccmc, 08-30-2019 03:23 PM
    • Replies: 1
    • Views: 752
    09-03-2019, 12:45 PM Go to last post
  10. Pre-load on needle roller clutch

    Started by csendegeya, 08-30-2019 09:35 AM
    bearings, clutch
    • Replies: 1
    • Views: 701
    08-30-2019, 10:21 AM Go to last post
  11. Angle Iron Stress

    Started by komet99, 04-03-2012 09:48 PM
    • Replies: 9
    • Views: 66,680
    08-28-2019, 01:31 PM Go to last post
  12. Heat Exchanger Question

    Started by belachavbelachavchavchavchav, 08-22-2019 03:14 PM
    • Replies: 1
    • Views: 776
    08-23-2019, 08:27 AM Go to last post
  13. Uni project Help

    Started by Prialen08, 08-21-2019 09:41 AM
    design, jockey wheel
    • Replies: 0
    • Views: 662
    08-21-2019, 09:41 AM Go to last post
  14. Low Friction Fabrics

    Started by benjamin_banks, 05-01-2019 12:51 AM
    fabric, fashion, friction, material, science
    • Replies: 5
    • Views: 1,152
    08-15-2019, 10:41 AM Go to last post
  15. Ways to lessen wear caused by a steel fixture

    Started by harrisonczaj, 07-15-2019 10:47 AM
    fixture design, part wear, plastic coating
    • Replies: 5
    • Views: 955
    08-15-2019, 10:38 AM Go to last post
  16. SolidWorks Stress Analysis question

    Started by thinds, 08-12-2019 10:50 AM
    • Replies: 2
    • Views: 563
    08-13-2019, 08:10 AM Go to last post
  17. Material "Slash sheet description"

    Started by sdicarlo, 07-31-2019 02:41 PM
    • Replies: 0
    • Views: 432
    07-31-2019, 02:41 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •