Page 1 of 18 1 2 3 11 ... LastLast
Threads 1 to 20 of 344

Forum: Dimensioning Tolerancing GD&T Discussion Forum | GD&T Training

Geometric dimensioning and tolerancing, limit tolerancing, drafting practices, GD&T, ASME Y14.5, GD&T training topics. GD&T Training

  1. Sticky Thread Sticky: ASME Y14.5-2009, Geometric Boundaries II GD&T Reference Book

    Started by administrator, 03-30-2014 02:41 PM
    • Replies: 2
    • Views: 18,169
    brianjonesengineer
    10-24-2020, 05:21 PM Go to last post

  2. Sticky Thread Sticky: GD&T Training ASME and ISO Standard Onsite

    Started by administrator, 03-30-2014 02:42 PM
    • Replies: 0
    • Views: 12,926
    administrator
    03-30-2014, 02:42 PM Go to last post

  1. Double Plus or Minus Tolerances

    Started by jjonas, 09-02-2013 06:49 PM
    • Replies: 5
    • Views: 77,263
    jjonas
    09-03-2013, 02:04 PM Go to last post

  2. Hole Tolerance for Press Fit dowel Pin

    Started by kelley_shreve, 03-29-2012 08:06 AM
    • Replies: 4
    • Views: 77,036
    Kelly_Bramble
    10-08-2012, 07:13 AM Go to last post

  3. Runout or Concentricity

    Started by Tactical14, 03-07-2013 07:51 PM
    2 Attachment(s)
    • Replies: 11
    • Views: 38,201
    Kelly_Bramble
    08-17-2013, 01:52 PM Go to last post

  4. Faro Arm vs CMM (Aerospace)

    Started by chevrollac, 04-02-2012 01:47 PM
    • Replies: 9
    • Views: 34,159
    jchasek
    03-09-2021, 12:10 PM Go to last post

  5. Apply GD&T on Threaded Feature?

    Started by clkwad, 08-18-2014 08:15 PM
    • Replies: 4
    • Views: 27,514
    Belanger
    08-27-2014, 10:39 AM Go to last post

  6. Direction to tap thread?

    Started by logos, 09-30-2011 12:37 PM
    • Replies: 5
    • Views: 25,474
    PinkertonD
    09-30-2011, 06:09 PM Go to last post

  7. Post position control of hole pattern without datum & modifier

    Started by Nitin Kamble, 11-07-2014 04:36 AM
    • Replies: 12
    • Views: 24,659
    Kelly_Bramble
    12-05-2014, 01:37 PM Go to last post

  8. Diametrical True Position with Zero Tolerance

    Started by cncguy, 03-19-2013 10:01 AM
    • Replies: 7
    • Views: 23,232
    cncguy
    03-26-2013, 02:51 PM Go to last post

  9. Question ASME Tolerances, Dimensions and decimal places

    Started by belinda63, 04-28-2015 03:26 PM
    • Replies: 2
    • Views: 22,178
    belinda63
    04-28-2015, 05:03 PM Go to last post

  10. Meaning of a radial tolerance

    Started by hufeddk, 01-09-2013 09:10 AM
    measurement, tolerance 1 Attachment(s)
    • Replies: 3
    • Views: 21,951
    Kelly_Bramble
    01-09-2013, 11:00 AM Go to last post

  11. Bang Head Question about: Basic dimension or Theoretically exact dimension (TED)

    Started by jeffmech, 02-21-2015 01:54 PM
    2 Attachment(s)
    • Replies: 5
    • Views: 21,303
    Kelly_Bramble
    02-26-2015, 02:49 PM Go to last post

  12. Open tolerance for drawing

    Started by dhanishd, 12-12-2011 10:30 PM
    • Replies: 2
    • Views: 21,268
    Belanger
    12-14-2011, 01:42 PM Go to last post

  13. Primary Datum

    Started by DougT, 04-26-2011 11:08 AM
    • Replies: 1
    • Views: 19,233
    Kelly_Bramble
    04-26-2011, 11:59 AM Go to last post

  14. Circularity / Roundness

    Started by Kanerva, 05-20-2011 12:50 PM
    1 Attachment(s)
    • Replies: 2
    • Views: 18,482
    Belanger
    05-26-2011, 07:25 PM Go to last post

  15. Thru holes in a hollow cylinder (pipe, tube, or hollow shaft)

    Started by jarey1968, 09-28-2011 08:20 AM
    • Replies: 7
    • Views: 18,441
    jboggs
    10-24-2011, 07:26 PM Go to last post

  16. Tolerance of holes shown on centerlines

    Started by hogpaw, 03-22-2013 09:17 AM
    1 Attachment(s)
    • Replies: 5
    • Views: 18,382
    Kelly_Bramble
    03-22-2013, 05:41 PM Go to last post

  17. Cool Baseline or chain dimensioning (Para 5.2.2 from 1994 removed in 2009)

    Started by vnangli, 03-08-2011 10:15 AM
    baseline or chain
    • Replies: 6
    • Views: 18,359
    dahsr
    07-11-2011, 10:26 AM Go to last post

  18. stated accuracy of portable CMM arm and real world usage

    Started by slimething, 03-05-2014 07:44 PM
    aacmm, cmm, faro, portable cmm, romer 1 Attachment(s)
    • Replies: 5
    • Views: 18,358
    andrea_abdallah
    05-15-2020, 02:33 AM Go to last post

  19. Wall Thickness Variation - GD&T

    Started by mmlj, 02-23-2012 07:47 AM
    ring, tube, wall thickness, wall thickness variation 1 Attachment(s)
    • Replies: 10
    • Views: 16,857
    Kelly_Bramble
    10-14-2014, 08:05 AM Go to last post

  20. Is it legal to use a Centerline as a Datum Feature?

    Started by Larat, 06-29-2014 07:06 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 16,450
    Kelly_Bramble
    06-29-2014, 08:31 PM Go to last post
Page 1 of 18 1 2 3 11 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules