Page 2 of 5 FirstFirst 1 2 3 4 ... LastLast
Threads 21 to 40 of 94

Forum: Codes & Standards Forum

Engineering codes, standards and other documentation topics

  1. Shraeder/Presta Cycle Tire Standards

    Started by richard_fox, 06-23-2018 02:30 AM
    2 Attachment(s)
    • Replies: 5
    • Views: 8,066
    petronextinternational
    01-24-2019, 11:41 PM Go to last post

  2. burrs on machined plastic gasket

    Started by dfike19380, 08-31-2011 10:58 AM
    • Replies: 4
    • Views: 8,065
    PinkertonD
    08-31-2011, 06:10 PM Go to last post

  3. Specification for NPT Taps

    Started by hogpaw, 05-17-2013 01:57 PM
    1 Attachment(s)
    • Replies: 9
    • Views: 7,915
    hogpaw
    05-23-2013, 07:42 AM Go to last post

  4. ISO to ANSI conversion

    Started by lydiaai, 08-09-2016 02:15 AM
    ansi, conversion, iso
    • Replies: 0
    • Views: 7,845
    lydiaai
    08-09-2016, 02:15 AM Go to last post

  5. Post RPR - Rupture pressure ratio

    Started by Warchief, 10-13-2011 03:06 PM
    • Replies: 0
    • Views: 7,805
    Warchief
    10-13-2011, 03:06 PM Go to last post

  6. European steels to ASTM

    Started by Bill M, 05-10-2011 03:13 PM
    • Replies: 1
    • Views: 7,617
    RWOLFEJR
    05-11-2011, 07:40 AM Go to last post

  7. Looking for specs for NA standard (DoD metric) fasteners

    Started by yakman2020, 11-13-2012 10:21 AM
    • Replies: 2
    • Views: 7,368
    yakman2020
    11-13-2012, 11:00 AM Go to last post

  8. din 867 standard

    Started by tlbong, 12-01-2014 10:00 AM
    din 867
    • Replies: 1
    • Views: 7,358
    Kelly_Bramble
    12-01-2014, 03:56 PM Go to last post

  9. HELP! Intergraph Caesar II UG HDPE pipe stress analysis

    Started by ppengg, 04-11-2016 01:46 PM
    caesar ii, intergraph, ug piping
    • Replies: 0
    • Views: 7,228
    ppengg
    04-11-2016, 01:46 PM Go to last post

  10. Number of Test Rings needed for Welding

    Started by axj6412@gmail.com, 09-13-2014 07:04 PM
    1 Attachment(s)
    • Replies: 2
    • Views: 7,106
    jackieann000
    10-08-2014, 10:53 PM Go to last post

  11. What's this paint defect standard?

    Started by mark_short, 12-09-2022 05:14 AM
    1 Attachment(s)
    • Replies: 3
    • Views: 6,970
    mark_short
    12-12-2022, 02:42 AM Go to last post

  12. 10-Degree Modified Square Thread

    Started by rafazoide, 08-22-2012 03:23 PM
    • Replies: 0
    • Views: 6,951
    rafazoide
    08-22-2012, 03:23 PM Go to last post

  13. Min Internal Thread Engagement Length

    Started by whtan02, 05-24-2013 10:21 AM
    • Replies: 3
    • Views: 6,930
    PinkertonD
    05-24-2013, 02:35 PM Go to last post

  14. EN grade vs. EN number

    Started by martin_jnsson, 12-18-2021 03:04 AM
    1 Attachment(s)
    • Replies: 8
    • Views: 6,796
    martin_jnsson
    12-23-2021, 02:33 AM Go to last post

  15. Safety Standard for polymeric materials used in automotive electronics

    Started by andrew_templeton, 10-13-2016 02:59 PM
    • Replies: 1
    • Views: 6,697
    jamessmith00444
    07-13-2018, 07:17 AM Go to last post

  16. Suitability of API 620/650 for low pressure tank at 316F

    Started by b8e, 11-04-2011 10:47 PM
    • Replies: 1
    • Views: 6,672
    Kelly_Bramble
    11-05-2011, 08:08 AM Go to last post

  17. Welding Certifications

    Started by jcs003, 01-22-2015 08:31 AM
    • Replies: 8
    • Views: 6,578
    jackieann000
    03-03-2015, 11:10 PM Go to last post

  18. ASME Code stamping(U Stamp)

    Started by tarafdar, 09-12-2011 01:07 PM
    • Replies: 0
    • Views: 6,501
    tarafdar
    09-12-2011, 01:07 PM Go to last post

  19. SMOTE Codes for matlab

    Started by mehrdadm2n, 11-04-2015 01:52 AM
    • Replies: 1
    • Views: 6,493
    Kelly_Bramble
    11-04-2015, 06:07 AM Go to last post

  20. Din Flange to ASME pipe joints

    Started by Slurry Pumper, 05-28-2015 09:33 AM
    • Replies: 0
    • Views: 6,419
    Slurry Pumper
    05-28-2015, 09:33 AM Go to last post
Page 2 of 5 FirstFirst 1 2 3 4 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules